Page 9;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 57744
EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ
I/*(,$"83%L8#$('4$"&8#
%K*,9%$.*%6MGLK6%LNJIKGFMG%EF;6GH%LM;IKNFGLIM%#*4$"&8%,$%$.*%+*3"88"83%&2%$."#%
5,8',7%"847'9"83%,77%$*Z$%'89*(%#'+.*,9"83#%$.*(*"8%+*2&(*%#*$%'/%&(%'#*%&2%$."#%/(&9'4$1
E*$$"83%,89%G*#$"83
GI%JK6!6MG%E6KLIPE%LMfPKH%;KIN%FOOLU6MGFT%IJ6KFGLIM-%
N,X*%#'(*%$.,$%$.*%G("33*(%"#%"8%$.*%&22?/&#"$"&8%,89%(*5&W*%"$#%S,$$*(V%
J,4X%+*2&(*%/*(2&(5"83%,8V%/(&4*9'(*%"8%$."#%#*4$"&81
F9]'#$"83%$.*%F'Z"7",(V%_,897*
The Auxiliary Handle can be placed in a variety of
positions to obtain an efficient working angle.
1. To adjust the Auxiliary Handle, turn the Handle
counterclockwise to loosen the Band.
2. Slide the Handle on or off the Rotary Hammer
or to the desired position then turn the
Handle clockwise to secure it in place.
P#"83%$.*%U*/$.%R,'3*
The Depth Gauge can be used to lock in a desired
depth and return to that depth setting with ease.
1. Turn the Auxiliary Handle counterclockwise,
then slide the Depth Gauge through the
Depth Gauge Slot on the Handle.
2. Position the Depth Gauge as needed, then turn
the Auxiliary Handle clockwise to secure the Depth
Gauge in place.
F9]'#$"83%$.*%;'84$"&8#
Adjust the Mode Selector to the desired function before
using the Rotary Hammer. Press the Release Button
and rotate the Mode Selector until it clicks in place
with the Indicator pointing to the desired function.
MIGLO6- Move the Mode Selector only when the
Motor is stopped. Attempting to move the Mode
Selector while the Motor is engaged will result in
abrupt bit rotation and can cause property damage.
MIGLO6- When moving the Mode Selector,
make sure it clicks into the desired position. If
not locked in place, the Mode Selector could
slip out of position resulting in tool damage.
G&%O."#*7-%%Rotate the Mode Selector to the Hammer
Mode setting. The tool will hammer when powered.
G&%K&$,$*%,%S"$-%%;&(%#,2*$V=%,7),V#%(*5&W*%+,$$*(V%
+*2&(*%'#"83%$."#%#*$$"831%Rotate the Mode Selector
to the Rotation Mode setting when rotating a bit.
G&%_,55*(0U("77- Rotate the Mode Selector
to the Hammer/Drill Mode setting. The
tool will hammer drill when powered.
G&%U("77- Rotate the Mode Selector to the Drill
Mode setting. The tool will drill when powered.
N&9*%
L89"4,$&(
_,55*(0U("77%
N&9*
U("77%
N&9*
_,55*(%
N&9*
K&$,$"&8%
N&9*
To Next Page
Loading...
