S.p.A.
F 1900
4
PACKING AND TRANSPORT
◊ WIDTH: 100 cm
◊ DEPTH: 47 cm
◊ HEIGHT: 63 cm
⇒ Remove the pow er mow er from its packing.
⇒
⇒⇒
⇒
Fix the handles to the handlebar support using the two screws and two knobs pre-mounted on the handle.
Make sure to position the control cables correctly.
⇒
⇒⇒
⇒
Fix the bar to the machine, by unspitting the spring (Picture 9 Ref. A) on the pin Ref. B. Thread the pin in the casing
Ref. C and thread the spring again (Ref. A). Take the little plastic cylinder (Picture 9 Ref. D), threat it in the grass
divider head Ref. E and threat all in the pin of the lever arm Ref. F, in the holes on the head and on the cylinder. Fix
the head Ref. E to the bar by screw ing tw o screw s Ref. G in the threaded holes on the bar.
⇒
⇒⇒
⇒
If the machine is to be transported, empty out the petrol tank and always apply the plastic protective strip to
the cutting bar blade. If E.S.M. type, please read the sheet enclosed.
IMPORTANT: THE PACKED MACHINE IS SUPPLIED WITH THE MOTOR WITHOUT OIL OR PETROL.
SAFETY RULES
•
Read carefully the operation and maintenance manual enclosed w ith the machine.
•
The use of the machine is prohibited to persons under 16 years of age.
•
The operator is liable for damages since the machine is under his control.
•
Those unfamiliar w ith the machine or w ho have never used it are obliged to read the operation and
maintenance manual before operation.
•
In case of transport, disassemble the bar and empty the petrol out of the tank.
•
If the machine is left unattended, ensure that it cannot start up again.
•
Before running the machine, the operator must have a 5 meter radius of free space around him.
•
Dry any petrol leaks.
•
Fill up the tank w ith the motor off. Filling the tank or transferring fuel must alw ays be performed outdoors, aw ay
from flames or heat sources. Do not smoke during this operation.
•
When mow ing in mountainous areas or on slopes, mow horizontally and use non-skid equipment on shoes and
w heels.
•
If the blade needs replacement, observe E.S.M. operation and maintenance procedures.
•
If the bar suffers impact, check the condition of the bar before resuming w ork.
•
Keep feet and hands far aw ay from the cutting bar and all rotating parts.
•
Do not run the motor w here ex haust containing carbon monox ide may accumulate.
•
Never use the mower incomplete or without its safety device.
•
Do not assemble/disassemble or clean the cutting bar or other equipment with the motor running.
•
Caution! When the clutch is engaged the cutting bar is alw ays in motion.
•
Caution! Do not mow areas w ith slopes ex ceeding 50%.
•
We w ill not be held liable for accidents caused by the failure to observe these rules.
STARTING AND STOPPING THE POWER MOWER
Every time you get ready to start the motor, make a careful check of the follow ing:
• Make sure that fuel is in the tank.
• Check the motor oil level: CAUTION: MACHINES OUT OF THE FACTORY DO NOT CONTAIN OIL IN THE MOTOR.
Make sure to add oil up to the level on the dipstick.
• CONSULT THE OPERATION AND MAINTENANCE MANUAL OF THE MOTOR UNDER "BEFORE START-UP"
• Make sure oil is up to the level in the gearbox (Picture 5 Ref. A)
• Check that all safety systems are released and functioning, especially the levers Ref. B and Ref. C Picture 6
• Press the "Primer" button three times in case of starting with the motor cold (Picture 1 Ref. 11) only version B&S.
• Always start the motor up outdoors.
• Bring the accelerator hand lever (Picture 6 Ref. "A”) to the "START" position, grasp the cord handle (Picture 7) and
pull it slightly until you feel some resistance, then pull harder. Make sure that the cord does not return by itself --
accompany it with your hand.
To Next Page
Loading...
