To Next PageTo Next Page
Need help?Do you have a question about the Best Barns Arlington-R and is the answer not in the manual?
General| Brand | Best Barns |
|---|---|
| Model | Arlington-R |
| Category | Lawn and Garden Equipment |
| Language | English |
Explains siding edges (LAP/Tongue) and nailing instructions for proper installation.
Lists all necessary tools and safety equipment required for shed construction.
Instructions for cutting and spacing floor joists and headers for the foundation.
Lists specific lumber and hardware components required for the floor system.
Details steps for assembling roof trusses using blocks, rafters, and studs.
Instructions on using gauge blocks for consistent and proper truss overhang.
Steps for assembling roof gables with studs, plates, and gussets.
Note on installing a 2x2 board for an optional gable window.
Guides cutting and fitting 4x8 siding panels onto the gable frame.
Instructions for cutting window openings in siding panels as needed.
Describes installing 2x4 rafters to create gable overhangs.
Guidance on positioning and marking 72" wall plates for studs.
Instructions for installing pre-cut wall studs and nailing frames.
Details fitting and nailing siding panels to the end wall frame.
Guidance on cutting and marking 92-1/2" wall plates for studs.
Instructions for installing pre-cut studs into the back wall plates.
Details fitting siding panels to the back wall frame, noting extensions.
Guidance on cutting and marking 89-1/2" wall plates for studs.
Instructions on butting frames, installing siding, and handling overlaps.
Instructions for cutting lumber and assembling the door header.
Lists studs, boards, and header for the door wall assembly.
Instructions for installing studs and the door header in the opening.
Details cutting and fitting siding panels around the door opening.
Guidance on marking 15'-2" front wall plates for stud placement.
Diagrams the door opening location and measurements on the front wall.
Instructions for installing center wall studs and the door header.
Details cutting and fitting siding panels to the front wall frame.
Guides cutting siding for window and door openings on the front wall.
Instructions for installing the final siding panel on the wall frame.
Instructions for positioning, joining, and securing wall panels at corners.
Guidance on using studs to brace wall panels and hold them straight.
Instruction to cut and remove the bottom 2x4 in door openings.
Instructions for cutting and installing 2x4 tie plates on front and back walls.
Instructions for cutting and installing 3' long 2x4s on the end walls.
Emphasizes installing lower trim before roof gables.
Instructions for installing 1x4 trim boards on sidewalls.
Instructions for installing corner trim boards on rear walls and sidewalls.
Instructions for drawing lines and marking 'X's for truss positioning.
Advises placing the wood gusset on the line and 'X' on the correct side.
Instructions for installing the gable on the back wall and securing it.
Details nailing the bottom edge of gable siding into the 1x4 trim.
Instructions for placing trusses and securing them with hangers.
Emphasizes bracing sidewalls first and checking building width.
Instructions for installing 4x8 loft flooring sheets onto the trusses.
Advises ensuring walls are straight and nailing the flooring correctly.
Highlights that sidewall trim should be installed before soffit panels.
Instructions for installing 96-3/4" long 1x4 corner trim on the back wall.
Instructions for installing 4' and 1x4-12' trim along the sidewall top.
Guides installing 10-5/8" soffit panels under truss overhangs.
Instructions for installing 1x6 trim flush with the 2x4 on the rear sidewalls.
Instructions for cutting and installing 1x6 trim flush with the 2x4 on the front gable.
Diagram showing placement of 4x8 sheathing panels on the back roof.
Guides sheathing installation, mentioning ventilation gaps and ply-clips.
Diagram showing placement of 4x8 sheathing panels on the front roof.
Instructions for installing 1x6 trim on end gables flush with the 2x4s.
Refers to a separate manual for cutting dormer openings.
Instructions for installing 1x6 trim boards over the 2x4s on the front gable.
Details installing jamb material and 1x4 trim boards around the door opening.
Directs to a separate manual for installing roof dormers.
Directs to a separate manual for installing pocket doors.
Instructions for installing metal roof edging along end walls and front edge.
Advises installing shingles according to wrapper instructions.
