BEST BUY essentials BE-CLOPP3 User Manual

Features
• Wake up to the radio or a buzzer
• Listen to either AM or FM stations
• Set snooze or sleep functions
• Program up to two dierent alarms
• Prevent losing the time with the pre-installed CR2025
backup battery
• Charge devices with the USB charging port
Front LED display
Back
Top panel
Setting up your clock radio
1 Pull out the plastic tab to activate the pre-installedCR2025
battery.
2 Connect the power adapter from your alarm clock's power jack to
a power outlet. The hour digits blink on the display.
3 Press (down) or (up) repeatedly to set the correct hour, then
press (radio/clock) to save the setting. The minutes digits
blink.
4 Press (down) or (up) repeatedly to set the correct minutes,
then press (radio/clock) to save the setting.
Notes:
• When you set the clock to a time after noon (12 PM), the PM indicator
lights.
• To set the clock again, press and hold (radio/clock) in standby
mode. When the hours digits blink on the display, repeat steps 3–4.
Before using your new product, please read these instructions to prevent any damage.
Package contents
• Alarm clock radio
• AC power adapter
• CR2025 battery
• Quick Setup Guide
AM/FM Dual
Alarm Clock Radio
Quick Setup Guide
BE-CLOPP3
#
1
2
3
4
5
6
7
Description
• Press and hold to turn the radio on or o.
• Press briey to switch between FM and AM.
With the radio turned o:
• Press and hold to set the clock.
With the radio turned on:
• Press briey to move to the next preset radio station.
• Press and hold for two seconds to save a new radio station preset.
• Press and hold for six seconds to automatically search and save radio stations.
With the radio turned o:
• Press briey to turn Alarm 1 on or o.
• Press and hold to set the alarm time.
With the radio turned o:
• Press briey to turn Alarm 2 on or o.
• Press and hold to set the alarm time.
• Press briey to adjust the screen brightness or to snooze when the alarm is
ringing.
• Press and hold to turn o the alarm when the alarm is ringing
• With the radio turned on, press and hold to set the sleep timer (90 min.,
60 min., 45 min., 30 min., 15 min., or OFF).
With the radio turned on:
• Press to tune the radio to the previous or next station.
• Press and hold to search for the station automatically.
When setting the clock:
• Press to set the hours and minutes backward or forward.
When setting the alarm:
• Use to adjust the alarm time, select the alarm mode, or adjust the
alarm volume.
Press to raise or lower the volume.
Item
Radio
power
Radio/Clock
Alarm 1
Alarm 2
Brightness/
Sleep/Snooze
Up/
Down
+ Raise/
- Lower volume
Using the alarm clock
Setting an alarm
1 Press and hold (Alarm 1). The hours digits blink.
2 Press (down) or (up) repeatedly to set the correct hour, then
press (Alarm 1) to save the setting. The minutes digits blink.
3 Press (down) or (up) repeatedly to set the correct minutes, then
press (Alarm 1) to save the setting.
4 Press (down) or (up) to select the alarm ring type (“Bu” for a
buzzer sound or “rAd” for the radio), then press (Alarm 1) to save
the setting.
5 Press (down) or (up) to set the volume, then press (Alarm 1)
to save the setting. Alarm 1 is turned on.
Notes:
• To set Alarm 2, follow these instructions, but press (Alarm 2) instead of
(Alarm 1).
• To turn on an alarm that you’ve previously set, press (Alarm 1) or
(Alarm 2). The Alarm 1 or Alarm 2 indicator is shown on the display
when the alarm is turned on.
Quieting an alarm
• Press SNOOZE briey to mute an alarm for nine minutes. You
can snooze as many times as you need within 59 minutes of the
preset alarm time.
• Press and hold SNOOZE to turn o an alarm for 24 hours. The
alarm stays on to ring the next day.
• Press (Alarm 1) or (Alarm 2) briey to cancel an alarm. The
indicator turns o, and the alarm remains o.
Time/Alarm/Frequency display
Sleep timer indicator
PM indicator
Alarm 1 ON indicator
Alarm 2 ON indicator
Using the radio
1 Press and hold (power) to turn on the radio.
2 Press (power) briey to select either the FM or AM band. The
current station is shown on the screen for 10 seconds, then
clock displays.
Note: If you select the FM band, stretch out the FM antenna on the
back of your clock radio to improve FM reception.
3 To tune into a station:
a. Press (down) or (up) repeatedly to nd the station
you want.
b. Press and hold (down) or (up) to search for the next
available station.
Note: The search may not stop at a station with a weak signal.
4 Press + (raise volume) or – (lower volume) to raise or lower the
volume.
5 When you nish listening, press and hold (power) to turn o
the radio.
Back
Power adapter
Back
Speaker
Power jack
USB port
FM antenna
Plastic tab

BEST BUY essentials BE-CLOPP3 Specifications

General

Brand	BEST BUY essentials
Model	BE-CLOPP3
Category	Clock Radio
Language	English

Summary

Setting Up Your Clock Radio

Activate Backup Battery

Pull out the plastic tab to activate the pre-installed CR2025 battery.

Connect Power Adapter

Connect the power adapter to the clock radio's power jack and a power outlet.

Set Clock Hour

Press Up/Down buttons to set the correct hour and save.

Set Clock Minutes

Press Up/Down buttons to set the correct minutes and save.

Using the Alarm Clock

Setting an Alarm

Detailed steps for setting alarm times, ring type, and volume.

Using the Radio

Powering On and Band Selection

Turn on the radio and select FM or AM band.

Tuning Stations

Tune to a station by pressing Up/Down or search automatically.

Adjusting Volume

Use the Raise/Lower volume buttons to adjust sound level.

Powering Off

Turn off the radio by pressing and holding the power button.

Saving Radio Station Presets

Saving a Preset Station

Select a preset number and radio band to save a station.

Exiting Preset Saving

Save changes and exit or automatically search and save stations.

Recalling Preset Stations

Using the Sleep Timer

Setting the Sleep Timer

Press and hold SNOOZE to set the sleep timer duration.

Stopping the Sleep Timer

Press and hold power to stop listening at any time.

Charging USB Devices

Adjusting LED Brightness

Maintaining Your Clock Radio

Specifications

Troubleshooting

No Power Issues

Check power adapter connection and outlet functionality.

No Sound from Speakers

Verify volume, adapter connection, and that the radio is on.

Static or Noise

Ensure correct tuning, good signal, and antenna placement.

Distorted Sound

Check volume level and signal quality.

Overheating

Normal for extended play; reduce volume to cool.

Safety Information

Legal Compliance

Warranty and Contact