Biolight Meditech S12 Vet

To Next Page

To Previous Page

S12 Vet Monitor User’s Manual

14-9



Problem Solution

2. Complete the injection smoothly within 4 to 5 seconds.

3. Check whether the C.O. cable, floating catheter and liquid

temperature sensor are connected or not.

Main Page

default chapter5
- Table of Contents5
Chapter 1 General Introduction11
- Intended Use11
- Main Unit11
- Screen Display15
Chapter 2 Safety22
- Safety Information22
- Equipment Symbols24
- Packaging Symbols25
Chapter 3 Basic Operations26
- Installation26
- Getting Started28
- Shutting off the Monitor29
- Operation and Browse30
- General Settings31
- Measurement Settings33
- Operation Mode35
- Using the Timer39
- Voice Assistant40
Chapter 4 Patient Management42
- Discharging a Patient42
- Admitting a Patient43
- Managing Patient Information43
- Connecting to a Central Monitoring System45
Chapter 5 Managing Configurations46
- Introduction46
- Selecting Default Configuration46
- Saving Current Settings46
- Deleting a Configuration47
- Transferring a Configuration47
- Loading Current Configuration48
- New Patient Usage Configuration48
- Monitor Boot Usage Configuration49
- Setting Password Valid Time49
Chapter 6 User Interface50
- Interface Style50
- Dynamic Trend Screen51
- Oxycrg Screen52
- Other Bed Observation53
- Big Font Screen57
- Freezing Waveforms57
Chapter 7 Alarm59
- Introduction59
- Safety Information59
- About the Alarm60
- Viewing Physiological Alarms List62
- Viewing Technical Alarms List62
- Setting Alarm62
- Alarm Pause67
- Alarm Reset69
- Latching Alarms69
- Nurse Call70
- Intubation Status72
- Other Bed Alarm73
- Detecting Alarm74
- Actions When an Alarm Occurs74
Chapter 8 ECG75
- Introduction75
- Safety Information75
- ECG Display76
- Preparing for ECG Monitoring77
- ECG Settings83
- Arrhythmia Monitoring89
- ST Monitoring91
- Qt/Qtc Monitoring98
- Isoelectric Segments103
- ECG Relearning103
- Calibrating ECG103
- Defibrillation Synchronization104
- ECG Troubleshooting105
Chapter 9 Respiration Rate (RESP)107
- Introduction107
- Safety Information107
- RESP Display108
- Placing RESP Electrodes108
- RESP Settings110
- RESP Troubleshooting112
Chapter 10 Spo2113
- Introduction113
- Safety Information114
- Monitoring Procedure115
- Setting Spo2115
- Setting PR117
- Spo2 Measurement Limitations118
Chapter 11 Temperature（Temp120
- Introduction120
- Displaying the TEMP Parameter Area120
- TEMP Display120
- Preparing for TEMP Monitoring121
- TEMP Settings121
- TEMP Troubleshooting122
Chapter 12 NIBP124
- Introduction124
- Safety Information124
- NIBP Measurement Limitations126
- Measurement Modes126
- NIBP Display127
- Preparing for NIBP Measurements128
- Starting and Stopping NIBP Measurements130
- NIBP Settings131
- Assisting Venous Puncture133
- NIBP Maintenance134
- NIBP Troubleshooting134
Chapter 13 IBP135
- Introduction135
- Safety Information135
- IBP Measurement136
- IBP Display137
- Setting IBP139
- IBP Troubleshooting143
Chapter 14 Cardiac Output (C.O.)145
- Introduction145
- Safety Information145
- Measurement Limitation145
- Display146
- Equipment Connecting147
- Measurement147
- Setting150
- Troubleshooting151
Chapter 15 Carbon Dioxide (CO 2 )154
- Introduction154
- Safety Information154
- CO2 Measurement Limitations155
- Monitoring Procedure155
- Display160
- Settings CO161
- Entering Intubation Status164
- Zeroing164
- Calibration165
- Exhaust Emission166
- Announcements166
- CO Troubleshooting168
Chapter 16 Drip Monitor (DM)169
- Introduction169
- Safety Information169
- DM Measurement170
- DM Module Indicator173
- DM Display173
- Setting DM174
- DM Check174
Chapter 17 Review175
- Review Overview175
- Reviewing Page175
Chapter 18 Calculations186
- Introduction186
- Safety Information186
- Drug Calculation186
- Hemodynamic Calculations189
- Oxygenation Calculation191
- Ventilation Calculations194
- Nephridium Calculation196
Chapter 19 Recording199
- Recorder199
- Recording Type199
- Starting Recordings200
- Stopping Recordings200
- Recording Flags200
- Setting the Recorder201
- Installing Recording Paper202
- Clearing Jam Paper203
- Cleaning Recorder203
Chapter 20 Other Functions205
- Analog Signal Output205
- Network Settings205
- HL7 Settings208
Chapter 21 Battery209
- Introduction209
- Installing a Battery209
- Battery Guidelines209
- Battery Maintenance210
- Battery Recycling212
Chapter 22 Maintenance and Cleaning213
- Introduction213
- Cleaning of the Monitor214
- Disinfection214
- Cleaning and Sterilizing of Accessories215
- Sterilization216
Chapter 23 Maintenance217
- Inspection217
- Maintenance Schedule218
- Disposing of the Monitor219
Chapter 24 Accessories220
- Recommended Accessories221
Appendix A Product Specifications225
- Safety Specifications225
- Environmental Specifications226
- Physical Specifications226
- Power Specifications227
- Hardware Specifications228
- Data Storage231
- Wireless Network231
- Measurement Specifications232
- Alarm Specification249
Appendix B EMC and Radio Regulatory Compliance252
- Emc252
- The Management Compliance of Radio258
Appendix C Default Settings259
- ECG, Arrhythmia, ST, QT259
- Resp262
- Spo2262
- Temp263
- Nibp264
- Ibp265
- C.o267
- Co2267
- Alarm Default Settings268
- Screen Setup269
- Color of Parameters269
- Recorder269
- Other270
- Maintenance Item270
Appendix D Alarm Message272
- Physiological Alarm272
- Technical Alarm274
Appendix E Cybersecurity284
- Operating Environment284
- Network Data Interface284
- User Access Control Mechanism284
- Software Environment285
Appendix F Terminology and Definitions286
- List of Units286
- Symbol List287
- Terminology List288
Appendix G Toxic and Harmful Substances or Elements292

Biolight Meditech S12 Vet - Page 153

Table of Contents

Related product manuals