The BlueSpot Coil Spring Compressor Set (model 07919) is an essential tool designed for the safe and efficient compression of coil springs on vehicles. This allows for the repair or replacement of shocks, springs, or struts. The set includes two coil spring compressors, each featuring a twin hook design for enhanced stability during operation.
Function Description:
The primary function of the BlueSpot Coil Spring Compressor Set is to compress coil springs, thereby releasing the tension that holds them in place on a vehicle's suspension system. This compression is crucial for safely removing and installing components such as shock absorbers, springs, and struts. The tool works by engaging hooks onto the spring coils and then tightening a central screw mechanism, which draws the hooks closer together, compressing the spring.
Important Technical Specifications:
- Material: Manufactured from heat-treated tempered steel, ensuring high strength and durability.
- Hooks: Features drop-forged steel hooks, which contribute to increased durability and secure gripping of the spring coils.
- Design: Twin hook design on each compressor provides enhanced stability and even compression across the spring.
- Compatibility: Suitable for use with coil springs up to 260mm in length.
- Tightening Mechanism: Requires a 19mm spanner for tightening the compression screw.
Usage Features:
- Safety First: The manual emphasizes the critical importance of safety during operation. Users are strongly cautioned against leaving a coil spring under tension due to the stored energy, which can be dangerous. Springs should be immediately replaced onto the shock absorber to minimize the time they are under tension.
- Pre-Operation Checks: Before use, it is imperative to ensure the tool is in good and clean condition. The work area should be clean, uncluttered, and well-lit. Users must maintain correct balance and footing, wear non-slip shoes, and keep children and unauthorized persons away.
- Personal Protective Equipment (PPE): Always wear appropriate PPE, including close-fitted clothing, tied-back long hair, removed jewellery, non-slip sole shoes, correct eye or face protection, and approved respiratory protection if needed.
- Engagement: To use, refer to the vehicle manufacturer's manual for shock absorber removal. Position the hook from the spring compressor over the shock absorber. Engage the hooks on the spring as far apart as possible, ensuring they are securely attached and correctly aligned. The two compressors should be parallel to each other.
- Compression Process: Compress the spring by using a 19mm spanner. It is crucial to apply equal turns to both compressors to ensure even compression and prevent the spring from becoming coil-bound.
- Critical Safety Warnings During Compression:
- DO NOT allow the spring to become coil-bound.
- NEVER use air tools to compress the spring, as this can cause serious injury or death.
- DO NOT leave a compressed spring unattended.
- ALWAYS be careful and pay attention while the spring is compressed, as it can be dangerous.
- Removal and Replacement: Once the spring is sufficiently compressed to allow rotation on the strut, remove the plate from the strut. The spring must remain compressed until after the strut has been replaced. When replacing the spring, reverse the compression procedure. DO NOT attempt to remove the spring from the compressors until all tension has been released.
- General Usage Restrictions:
- DO NOT use if the tool is damaged.
- NEVER operate the tool under the influence of drugs or alcohol.
- NEVER make modifications to the tool.
- NEVER use the spring compressor for tasks it was not designed for.
- DO NOT operate if tired.
- ALWAYS stop using the tool if experiencing discomfort or pain and consult a health professional if needed.
Maintenance Features:
- Cleaning: To clean the tool, simply use a dry cloth to wipe over it. This helps maintain its condition and performance.
- Storage: Store the spring compressors in a cool, dry area, out of reach of children. Proper storage helps prevent damage and extends the lifespan of the tool.
Disposal:
- When the tool is no longer functional or repairable, it should be disposed of according to national regulations.
- Contact your local waste disposal authority for information on correct disposal methods.
- The product, accessories, and packaging should be sorted and taken to a recycling centre. If the product becomes unserviceable and contains fluids, drain them into approved containers and dispose of them according to local regulations, ensuring environmental protection.
The BlueSpot Coil Spring Compressor Set is a robust and reliable tool, designed with user safety and efficiency in mind for automotive suspension work.
Need help?
General
To Next Page