3.3.3. Setting of the cutting angle ........................................................................................... 50
3.3.4. Setting of the optimal span of the guiding cubes ..................................................... 51
3.3.5. Cutting speed adjustment ............................................................................................. 52
3.3.6. Speed adjustment of the arm lowering ...................................................................... 52
3.3.7. Setting the type of cooling ............................................................................................ 52
3.4. Material insertion ............................................................................................................................ 53
3.4.1. Selecting means of manipulation ................................................................................. 53
3.4.2. Insertion ............................................................................................................................. 53
3.4.3. Bundle material cutting .................................................................................................. 53
4. ÚDRŽBA STROJE / MACHINE MAINTENANCE / WARTUNG .. 54
4.1. Saw band dismantling .................................................................................................................... 56
4.2. Saw band installation ..................................................................................................................... 58
4.3. Saw band stretching and inspection .......................................................................................... 60
4.3.1. Saw band stretching ........................................................................................................ 60
4.3.2. Saw band inspection ........................................................................................................ 61
4.4. Adjustment ....................................................................................................................................... 62
4.4.1. Saw band run adjustment .............................................................................................. 62
4.4.2. Hard metal guides adjustment on the machine ....................................................... 62
4.4.3. Guiding cube adjustment............................................................................................... 63
4.4.4. Brush adjustment ............................................................................................................. 63
4.4.5. Adjusting the limit switch of the saw band stretching ............................................. 65
4.4.6. Saw frame lower position stop adjustment ............................................................... 66
4.4.7. Adjustment of the limit switch of saw frame lower stop ......................................... 67
4.5. Cooling agents and chip disposal ............................................................................................... 68
4.5.1. Coolant inspection ........................................................................................................... 68
4.5.2. Chips disposal ................................................................................................................... 69
4.6. Gearbox oils and greases .............................................................................................................. 69
4.6.1. Gearbox oils ...................................................................................................................... 69
4.6.2. Lubrication greases .......................................................................................................... 71
4.7. Machine cleaning ............................................................................................................................. 71
4.8. Worn pieces replacement ..............................................................................................................72
4.8.1. Hard metal guides replacement ................................................................................... 72
4.8.2. Saw band guiding rollers replacement ....................................................................... 73
4.8.3. Worn brush replacement ............................................................................................... 75
4.8.4. Stretching wheel replacement ...................................................................................... 76
4.8.5. Driving wheel replacement ............................................................................................ 78
5. ZÁVADY / TROUBLESHOOTING / STÖRUNGEN ................... 81
5.1. Mechanical problems ..................................................................................................................... 83
5.2. Electrical problems .......................................................................................................................... 85
6. SCHÉMATA / SCHEMATA / SCHEMATICS ........................... 87
6.1. Elektrické schema /Elektroschema /Wiring diagrams ............................................................. 89
6.1.1. 3x400V+N+PE, 50Hz ES-101.180-B1/B2-V2.0 ............................................................ 89
6.1.2. 3x230V+PE, 50Hz ES-101.180-B3/T3-V2.0 ................................................................. 99
6.2. Hydraulické schéma / Hydraulikschema / Hydraulic diagram ........................................... 110
7. VÝKRESY SESTAV PRO OBJEDNÁNÍ NÁHRADNÍCH DÍLŮ /
ZEICHNUNGEN FÜR BESTELLUNG DER ERSATZTEILE / DRAWING
ASSEMBLIES FOR SPARE PARTS ORDER ..................................... 113
7.1. Easycut 275.230 DG........................................................................................................................114
7.2. Kusovník / Piece list / Stückliste - Easycut 275.230 DG .......................................................... 115
7.3. Easycut 275.230 DG........................................................................................................................ 116
7.4. Kusovník / Piece list / Stückliste - Easycut 275.230 DG .......................................................... 117
7.5. Chlazení / Cooling / Kühlung ....................................................................................................... 118
7.6. Kusovník / Piece list / Stückliste - Chlazení / Cooling / Kühlung ......................................... 119
7.7. Vana / Tank / Wanne .................................................................................................................... 120
7.8. Podstavec / Base / Untersatz ....................................................................................................... 121
7.9. Ovladací panel / Control panel / Bedienpult ........................................................................... 122
7.10. Kusovník / Piece list / Stückliste - Ovladací panel / Control panel / Bedienpult .... 123
7.11. Konzola otočná / Turnable consol / Drehkonsole ................................................................. 124
To Next Page
Loading...
Need help?
General
