Need help?Do you have a question about the BOON EDAM Speedlane 900 and is the answer not in the manual?
General| Brand | BOON EDAM |
|---|---|
| Model | Speedlane 900 |
| Category | Turnstiles |
| Language | English |
Covers copyright, liability, product modifications, options, abbreviations, and symbols.
Lists all abbreviations used in the manual, such as FI, LCD, LED, MCB, N.C., N.O., PCB, UPS.
Explains the warning and caution symbols used throughout the document for safety.
Critical safety warnings for installation and maintenance procedures.
Safety guidelines for proper operation of the Speedlane 900.
Overview of Speedlane 900 construction, dimensions, and capacity.
Details the motors, gearbox, angle encoders, and control system.
Explanation of the spring unit's function in compensating door wing weight.
Description of the microcontroller board (MCB), frequency inverter (FI), and multibeam receiver (MBR).
Details the multibeam sensor system, its layout, and function.
Explains operating modes (normal closed/open), direction types, and access control.
Details security features like intruder, opposite direction, tailgating alarms, and security modes.
Covers safety features: optical, mechanical, power failure, and fire alarm.
Describes system feedback via displays, signals, and other alarms.
Information on connecting and utilizing the external control panel.
Step-by-step guidance for the physical installation of the Speedlane 900.
Covers packaging, tools, anchoring methods, and electrical connections for installation.
Details floor layout for standard/wide lanes and conduit requirements.
Explains anchoring points and methods for installing the Speedlane 900.
Instructions for removing top and side panels for installation access.
Guidance on anchoring the unit to the floor, including using mounting plates.
Instructions for installing the glass door wings, including high cabinet glass.
Details the cables required for connecting master and slave units.
Outlines external connections for mains power, fire alarm, and access control.
Specifies internal and external connection points on the MCB and other components.
Lists all connections to the Microcontroller Board (MCB) for various functions.
Details the Multibeam system, its modules, and anti-masking detection.
Illustrates the sensor placement for different Speedlane 900 models.
Explains sensor functions like closing after passage, safety zone, and return signal.
Covers the start-up procedure, calibration, testing, and running-in of the Speedlane 900.
Identifies and explains the function of buttons on the MCB.
Describes the menu system for adjusting Speedlane 900 settings.
Lists and explains various menu items for configuration.
Explains standard and alternative signalling modes for status indication.
Details the options for selecting security levels: Low, Medium, and High.
Allows selection of the Speedlane 900 model and associated sensor configurations.
Explains the four steps for adjusting the door closing speed.
Options for selecting sensor activity: All sensors active or Spare sensors.
Adjustable time for passage after authorization.
Adjustable time authorization remains active after a person steps back.
Adjustable duration of the pulse sent to the access control system.
Options for gate opening: Sensor open or Pulse open.
Settings for the intruder alarm: On, Partial, or Off.
Monitors and displays error codes and status of the Speedlane 900.
Displays values from master and slave angle encoders for diagnostics.
Monitors the state and operation of the multibeam sensors.
Sets the maximum number of authorizations that can be stored.
Enables or disables the buzzer for alarms and signals.
Configures the gate's action during low battery power: open or close.
Selects the card reader mode for signal processing.
Configures modes for free passage: Normal or Special.
Selects the model of the frequency inverter used.
Resets all Speedlane 900 settings to factory defaults.
Details the integrated control panel of the Frequency Inverter for configuration.
Step-by-step guide on how to change parameter settings via the control panel.
Procedure for returning frequency inverter parameters to factory defaults.
Details default parameter settings required after a factory reset for specific models.
Instructions for updating the Speedlane 900 software using Flash Magic.
Configuration of COM port, Baud Rate, Device, and Oscillator Frequency.
Selection of blocks to be erased during software upload.
Procedure to select the Hex file for uploading.
Option to verify programming after the software upload.
Starting the software upload process and exiting programming mode.
Steps for mounting the middle cover plate and connecting sensor wiring.
Instructions for installing side covers and connecting the earth cable.
Guidance on attaching the top plates, whether one or two pieces.
A comprehensive list of spare parts for the Speedlane 900.
Overview of maintenance procedures and checks.
General checks and procedures for technicians during maintenance.
Checks for safety functions, sensors, wiring, and motor unit.
Checks for floor mountings, motor mountings, and overall alignment.
A checklist for performing regular maintenance on the Speedlane 900.
General warnings and guidance for troubleshooting issues.
Troubleshooting steps for issues related to the Microcontroller Board (MCB).
Lists Speedlane 900 error codes and their possible causes/actions.
Details error codes specific to the Frequency Inverter and their definitions.
Troubleshooting common problems related to the Uninterruptible Power Supply (UPS).
Summarizes other potential errors and their solutions, including door movement and LED issues.
Provides detailed specifications for motor, control, sensors, and barrier.
Specifications for the motor, including power, voltage, speed, and protective systems.
Specifications for the microcontroller and frequency inverter.
Specifications for the sensors, including power, distance, and response time.
Overall specifications for the barrier, including type, application, capacity, and finish.
A comprehensive list of spare parts for the Speedlane 900.
Checklists for configuring Frequency Inverter parameters for different Speedlane models.
Specific checklist for Wide and High Speedlane 900 inverter parameter settings.
Details major changes in software versions and compatibility notes.
Visual representation of the Speedlane 900's menu hierarchy and options.
To Next Page