Bosch CMG7361B1M - Page 18

en Ventilation function "Crisp Finish"
18
Requirement:Observe the information about the re-
spective operating mode.
→"Setting options with the microwave", Page17
1.
Press the operating mode that you require in the
menu.
2.
Select the settings for the operating mode, e.g. type
of heating and temperature.
3.
Press ⁠"Added microwave".
4.
Use the setting ring to set the microwave output.
5.
To confirm the set microwave output, press on
the display.
6.
Press ⁠ "Cooking time" and set the cooking time.
7.
Press to start the operation.
a The appliance starts to heat and the time counts
down.
a When the time has elapsed, a signal sounds. A
message appears on the display confirming that the
operation has finished.
8.
Once the cooking time has elapsed:
‒ If required, you can select other settings and re-
start the operation.
‒ When the food is ready, use to switch the ap-
pliance off.
Changing added microwave
You can change or deactivate the added microwave at
any time.
1.
Press on the display.
2.
Press the microwave output ⁠.
3.
Change or deactivate added microwave with the
setting ring.
4.
To confirm the change, press on the display.
a The change is applied.
Ventilation function "Crisp Finish"
12 Ventilation function "Crisp Finish"
V
e
n
t
-
i
l
-
a
-
t
i
o
n
f
u
n
c
-
t
i
o
n
"
C
r
i
s
p
F
i
n
-
i
s
h
"
The ventilation function "Crisp Finish" extracts mois-
ture from the cooking compartment so that your food
will be more crispy.
Hot steam that may escape when the appliance door is
opened is reduced.
12.1 Suitable types of heating with the
ventilation function
Only certain types of heating are suitable for the ventil-
ation function.
You can use the ventilation function for the following
types of heating:
¡ 4Dhot air
¡ Top/bottom heating
¡ Circulated air grilling
¡ Pizza setting
12.2 Setting the ventilation function
You can activate the ventilation function at any time,
even after the start of the operation.
1.
Set a suitable type of heating and a temperature.
If required, you can select other settings and com-
bine with the ventilation function.
2.
Press ⁠"Crisp Finish".
a The symbol lights up red.
3.
Press to start the operation.
a The appliance starts heating.
a The setting values are shown on the display.
4.
When the food is ready, use to switch the appli-
ance off.
Note:Amplified fan noises can be heard while the ap-
pliance is in operation.
Cancelling the ventilation function
You can switch off the ventilation function at any time.
1.
Press on the display.
2.
Press ⁠ "Crisp Finish".
a The symbol changes back to white.
a The operation continues without the ventilation func-
tion.
Dishes
13 Dishes
D
i
s
h
e
s
The "Dishes" operating mode helps you to use your ap-
pliance to prepare different meals by selecting the op-
timum settings automatically.
13.1 Cookware for dishes
The cooking result depends on the composition of the
meat and the size of cookware.
You should therefore use heat-resistant cookware that
is suitable for temperatures up to 300°C. Glass or
glass ceramic cookware is best. The joint should cover
approx.2/3 of the cookware base.
Cookware made from the following material is not
suitable:
¡ Bright, shiny aluminium
¡ Unglazed clay
¡ Plastic or plastic handles
Note:For some dishes, the appliance switches on the
microwave. A notification appears in the display stating
that you should use cookware that is suitable for mi-
crowave use.
→"Cookware and accessories with microwave",
Page16
13.2 Setting options for the dishes
To cook the dishes perfectly, the appliance uses differ-
ent settings depending on the dish.
The display shows you the settings that are used. You
can adjust certain settings. Follow the instructions on
the display.
Note:The cooking result depends on the quality and
composition of the food. Use fresh and, ideally, chilled
food. Use frozen food straight from the freezer.