Regulations
11
Condens 7000 F – 6720871560 (2019/11)
Table 3 Measurements and connection dimensions
3Regulations
DANGER:
Failure to comply with instructions may result in material damage
and personal injury, including danger to life!
Comply with all instructions.
NOTICE:
Risk of system damage due to differing operating conditions!
Faults may arise if the specified operating conditions are disregarded.
Where there is serious disregard for the stated operating conditions,
individual components or the boiler itself may be destroyed.
Observe the binding information on the data plate.
3.1 Regulations for gas systems
In order to ensure installation and operation of the product in
accordance with the regulations, please observe all the applicable
national and regional regulations as well as all technical rules and
guidelines.
The document 6720807972 contains information about the applicable
regulations. You can use the document search on our website to display
this. You will find the address of the website on the back of these
instructions.
3.2 Duty to obtain a permit and provide notification
Prior to installation of the heating and flue system:
Inform relevant building authority.
If required by the Clean Air Act 1993, seek approval for the flue
system from the Local Authority. For additional guidance see IGE/UP/
10 edition 4.
Make sure that there are no concerns on the part of the authority
regarding the planned installation
Make sure that official requirements are complied with.
Please note that in certain regions approvals may be required for the
flue system and the connection of the condensate outlet to the public
sewerage system.
3.3 Validity of regulations
Modified regulations or supplements are also valid at the time of
installation and must be observed.
3.4 Notes on installation and operation
Use only genuine spare parts from the manufacturer. The manufacturer
can assume no liability for damage caused by spare parts not supplied by
the manufacturer.
When installing and operating the heating system, observe the following
requirements:
• The local building regulations regarding installation conditions.
• The local building regulations regarding the supply and exhaust air
systems, and the chimney connection.
• Latest edition of the IEE Wiring regulations governing electrical
connection to the mains power supply
• Regulations and standards regarding the safety equipment in water-
filled heating systems. For guidance see the ICOM water treatment
guide for commercial heating systems.
• Make sure that the regional approvals required for the flue system
and condensate connection to the public sewage system have been
obtained.
Height H
AKO
mm 257 257 257 257 177 177 177 177 177 177 177 177
Height H
EL
mm 455 455 455 455 177 280 177 280 177 280 177 280
Height H
RLU
mm 176 176 176 176 163 163 163 163 163 163 163 163
Height H
VK
mm 1340 1340 1340 1340 1343 1343 1343 1343 1343 1343 1343 1343
Height H
RK
mm 554 554 554 554 552 552 552 552 552 552 552 552
Height H
VSL
mm 1520 1520 1520 1520 1520 1520 1520 1520 1520 1520 1520 1520
Height H
GAS
mm 1570 1570 1570 1570 1620 1620 1620 1620 1620 1620 1620 1620
Length L mm 736 736 736 736 914 914 1317 1317 1317 1317 1317 1317
Length L
K
mm 594 594 594 594 845 845 1250 1250 1250 1250 1250 1250
1) Right-hand version
2) Left-hand version
3) Female thread (Table 7, page 18)
4) PN6 standard flange, EN1092 (Table 7, page 18)
Boiler size (output in kW)
Unit 75
1)
75
2)
100
1)
100
2)
150
1)
150
2)
200
1)
200
2)
250
1)
250
2)
300
1)
300
2)
To Next Page
Loading...
