Bosch D7212GV3

To Next Page

To Previous Page

D7212GV3 | Operation and Installation Guide | Notes

Bosch Security Systems, Inc. | 10/10 | F01U143079-03 57

Notes

Main Page

Table of Contents3
Introduction6
Related Documentation6
Lightning Strikes7
Effects7
Precautions During Installation7
Overview8
Configuration and Parts8
Figure 1: System Configuration8
GV3 Series Control Panel Differences8
Parts List9
Parts Available by Separate Order9
Accessories10
Compatible Accessories10
Features in the D7212GV311
SDI Molex Connector11
Tip and Ring Posts11
Telephone Line Sniff11
Points11
Areas and Accounts11
Digital Communicator11
Keypads11
Keyswitch12
Event Memory12
Event Log12
Ground Fault Detection12
Ground Fault Detection Added Feature12
Conettix Functions12
Programming12
Compatible Keypads12
Other Features13
Installation13
Installation Preparation13
Enclosure Options13
Mounting Enclosure13
Figure 2: Enclosure Mounting14
Installing the Control Panel15
Connecting Earth Ground15
Terminal 1015
Ground Fault Detect Enable15
Enabling Ground Fault Detection15
D7212GV3 Ground Fault Specifications15
Locking the Reset Pin15
Figure 3: Ground Fault Detect (S4)15
Completing the Installation16
Charging the Battery16
Installing and Wiring Detection Devices16
Installing Modules and Relays16
Connecting the On-Board Points and Keypads16
Figure 4: Reset Pin16
Powering up17
Programming the Control Panel17
Installing the Point Chart Label17
Testing the System17
Service Walk Test17
Figure 5: Service Walk Test Flow Chart19
Power Supply20
Primary Power Terminals 1 and 220
Primary (AC) Power Circuit20
Installing the Transformer20
Secondary Power Terminals20
Secondary (DC) Power20
Installing the Battery21
Replacing the Battery21
Battery Supervision21
Figure 6: Battery Terminals21
Battery Charging Circuit22
Battery Discharge and Recharge Schedule22
Figure 7: Charging and Battery Leds22
Ground Fault Impedance Specifications 15 Battery Discharge and Recharge Schedule22
Power Outputs24
Circuit Protection24
Total Available Power24
Continuous Power Output Terminals 3, 8, and 3224
Programmable Power Output Terminals 6, 7, and 824
Programming24
Terminals 6 and 725
Fire System Power Formula25
Terminal 825
Telephone Connections25
Registration25
Notification25
Location26
Telephone Cord Connection26
Figure 8: RJ31X Wiring26
Operation Monitor LED Locations26
Phone LED (Red)27
Operation Monitor LED (Green)27
Dialing Format27
Telephone Line Monitor27
Called Party Disconnect27
Communication Failure27
On-Board Points28
Terminals 11 to 22 Description28
Point Sensor Loops28
Point Parameters28
Figure 10: On-Board Point Sensor Loop Wiring28
Charging Status and Low Battery Leds. 23 Point Parameters28
Point Response Time29
Wiring Information for Installations Using the Rothenbuhler 5110/4001-42 High Security Bell29
Figure 11: Rothenbuhler 5110/4001-42 High Security Table 11: Bell Wiring Configuration30
Figure 12: Wiring the Rothenbuhler 5110/4001-4231
Control Panel31
Off-Board Points32
Point (Zonex) Bus: D7212GV3 Terminals32
POPIT Modules32
POPEX Modules32
Missing Conditions32
Extra Point Events32
D7212GV3 Responses to Missing Point33
Conditions33
D8125, D9127 POPIT Modules33
Off-Board Point Errors33
Figure 13: Connecting the D8125 POPEX to the D7212GV3 Control Panel34
Installing the D8125 POPEX Module35
Mounting35
Wiring the D8125 to the Control Panel35
Wiring Popits to the Data Expansion Loop3535
Data Expansion Loop Wire Specifications35
Wiring Data Expansion Loops to POPEX Modules36
POPIT Sensor Loops36
POPIT Module Point Assignments36
Program Record Sheet36
POPIT Labels37
D8128D Octopopit Module37
Description37
Listings37
Figure 14: Program Record Sheet37
Installation38
Setting the Octopopit Switches38
Figure 15: D8128D Octopopit Layout38
D8128D Octopopit Switch Settings38
Mounting Octopopits39
Wiring Octopopits39
Switch 5 Settings for Line Termination39
Terminal Strip Connections39
Figure 16: Connecting D8128D Octopopits to the40
D7212Gv340
Figure 17: Wiring Multiple D8128Ds Using Molex41
Connectors41
Octopopit Sensor Loops42
Testing Off-Board Points42
Figure 18: D8128D Octopopit Sensor Loops42
Off-Board Relays43
D8129 Octorelay43
Configuring the D8129 Octorelay43
Figure 19: D8129 Connections to the D7212GV343
D8129 Octorelay Switch Settings43
Relay Outputs44
Installation44
Wiring Connections44
Arming Devices44
Description44
Keypad Terminals 29 to 3244
Assigning an Address for the Keypad45
Installation45
Keypad Address Settings45
Keypad Connections45
Figure 20: Power at Keypads46
D279A Independent Zone Control47
Keyswitch47
Description47
Programming47
Installation47
Operation47
Figure 21: Keyswitch Wiring47
SDI Devices48
Description48
Installation48
D9131A Parallel Printer Interface Module48
Switch Settings48
Supervision48
SDI Address 88 and 9248
Network Interface Modules48
SDI Device Connections48
Printer Address Switch Settings48
Address Settings49
Supervision49
Programmer Connections49
Programmer Connector49
Figure 22: DX4020 DIP Switch Settings49
Figure 23: Reset Pin49
Installer Keypad and Local Programmers Mode50
Programmer Access Reports50
D7212GV3 Faceplate51
Appendix A: System Wiring Diagrams, Issue a52
Appendix B: Point Address Chart55
Zonex 1, Points 9 to 4055
Specifications56
SDI Bus a (+)56
Connection56
Discharge Cycle56

Bosch D7212GV3 - Notes

Table of Contents

Other manuals for Bosch D7212GV3

Related product manuals