Bosch Dremel VERSAFLAME 2200 - Getting Started and Use; Getting Started; Operating the Tool; Flame Adjustment

butane gas
Make sure the gas you are using is rened butane gas
that can also be used for lighters
1 Hold the tool and the gas rell container as shown
in
3

2 Fill the gas tank with liquid butane gas observing
the instructions on the rell container The gas
tank is full when liquid butane gas escapes
through the lling valve In that case, there is no
more air present in the gas tank
!
DO NOT OVERFILL THE GAS TANK. Overlling
occurs when no air escapes from the tank while
lling it. In this case please use a different tip on the
gas tank with which you are lling, to allow air to
escape from the tank.
USE
GETTING STARTED
Familiarize yourself with the components of the tool
2

The tool is equipped with a child-safety mechanism
which requires a two-step operation to protect against
accidental ignition
ON/OFF
To switch on and operate the tool
4
:
1 The air control lever must be in the open position
4
a
2 The lock button must be in the forward position for
the tool to be able to ignite
4
b
3 Hold the tool in one hand
4 With your other hand move the child-safety lock
to the left
4
c
5 Slowly press the ignition button and hold it down
4
d
6 When using the catalyst: close the air control
lever for 2 seconds and re-open it to prevent the
catalyst from being overheated
4
e
After ignition, make sure that the tool is
switched on by checking that the catalyst
starts to glow.
7 To switch off the tool, release the ignition button
This will immediately shut off the ow of butane
gas
To operate the tool continuously
5
:
1 Switch on the tool as described above
2 Slide the lock button backward and release the
ignition button
3 To switch off the tool, slide the lock button forward
This will immediately stop the ow of butane gas
USING WITH AN OPEN FLAME
The tool can only be used with an open ame if the
catalyst is removed
FLAME LENGTH AND TEMPERATURE
ADJUSTMENT
Move the ame control lever forward to increase
the ame length and temperature, or backward to
decrease the ame length and temperature
When using an open ame, the tool is at the desired
temperature immediately after ignition
Please allow approximately 25 seconds of heat-up
time for the soldering tip
ACCESSORIES
!
ALWAYS SWITCH OFF THE TOOL AND ALLOW
IT TO FULLY COOL DOWN BEFORE
ATTACHING OR REMOVING ACCESSORIES
CATALYST B 6
The catalyst generates hot air of 680°C (used for
melting plastics and other heat-sensitive materials):
1 Slide the narrow part of the catalyst into the
burner Make sure the slot of the catalyst is
aligned with the white indicator mark
2 To remove the catalyst, slide it out of the burner
SOLDERING TIP A 7
The soldering tip, to be used on the catalyst (used for
regular soldering activities, using soldering tin):
1 Screw the soldering tip in clockwise direction
onto the catalyst Secure the tip using the 7 mm
wrench provided
2 To remove the soldering tip, use the 7 mm wrench
to unscrew the tip in counter-clockwise direction
FLAME EXTENSION PIECE L 8
The ame extension piece generates hot air of approx
1000°C (used for heating larger surfaces):
1 Loosen the screw to t the front tip (screwdriver
not included)
DEFLECTOR M 8
To be used with the ame extension piece
MAINTENANCE AND CLEANING
!
ALWAYS SWITCH OFF THE TOOL AND ALLOW
IT TO FULLY COOL DOWN BEFORE CLEANING
Clean the exterior of the tool with a clean cloth If
necessary, use a damp cloth with a small amount of
neutral detergent
After soldering or in case of excess solder on the
soldering tip, wipe the tip on a soldering sponge
soaked in some water when it is still hot
Never clean the soldering tip with sandpaper as this
reduces its lifetime
SERVICE AND WARRANTY
We recommend that all tool service be performed by a
Dremel Service Centre
This Dremel product is guaranteed in accordance with
statutory/country-specic regulations; damage due to
normal wear and tear, overload or improper handling
are excluded from the warranty
In case of a complaint, send the undismantled tool
and/or charger and proof of purchase to your dealer
CONTACT DREMEL
For more information on service and warranty, the
Dremel product range, support and hotline, go to
wwwdremelcom
5