Bosch EasySaw 18V-70 - Technical data; Noise;Vibration Information; Assembly; Battery Charging

English | 17
Technical data
Jigsaw EasySaw 18V-70
Article number
3603K120..
Stroke rate control ●
Rated voltage V= 18
No-load stroke rate n₀ min
−1
2600
Stroke mm 20
Max. cutting depth
– in wood mm 70
– in aluminium mm 15
– in steel (unalloyed) mm 6
Max. cutting angle (left/right) ° 45
Weight according to EPTA-Pro-
cedure01:2014
A)
kg 1.7 (1.5Ah)–
2.0 (6Ah)
Recommended ambient temper-
ature during charging
°C 0to+35
Permitted ambient temperature
during operation
B)
and during
storage
°C –20to+50
Recommended rechargeable bat-
teries
PBA 18V…W-.
Recommended battery char-
gers
C)
AL 18…
A) Depends on battery in use
B) Limited performance at temperatures <0°C
C) The following chargers are not compatible with the PBA re-
chargeable battery: AL 1814 CV, AL 1820 CV, AL 1860 CV
Noise/Vibration Information
Noise emission values determined according to
EN62841‑2‑11.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 82dB(A); sound power level
93dB(A). Uncertainty K=5dB.
Wear hearing protection!
Vibration total values a
h
(triax vector sum) and uncertainty K
determined according to EN62841‑2‑11:
Cutting boards with saw bladeT144D:
a
h,B
= 8.5m/s
2
, K = 2.5m/s
2
,
cutting sheet metal with saw blade T118A:
a
h,M
= 10m/s
2
, K = 2m/s
2
.
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
u Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Battery Charging
u Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
To remove the battery (4), press the release button (5) and
pull the battery upwards and out of the power tool. Do not
use force to do this.
Battery charge indicator
The battery charge indicator (3) indicates the charge condi-
tion of the battery when the power tool is switched on. It
consists of three green LEDs.
LEDs Capacity
3 × continuous green light 66–100%
2 × continuous green light 33–66%
1 × continuous green light 11–33%
1 × slowly flashing green light 0–10%
The three LEDs in the battery charge indicator (3) flash
quickly when the temperature of the battery is outside the
operating temperature range of −20 to +50°C and/or the
overload protection has been triggered.
Bosch Power Tools 1 609 92A 64Y | (12.07.2021)