Bosch GBM 13-2 RE PROFESSIONAL - Technical Data; Declaration of Conformity

14 | English
1 609 92A 1CG | (23.6.15) Bosch Power Tools
Technical Data
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards: EN 60745-1,
EN 60745-2-1.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 23.06.2015
Assembly
Auxiliary Handle (see figure A)
 Operate your machine only with the auxiliary handle 9.
The auxiliary handle 9 can be set in 12 positions to achieve a
safe and low-fatigue working stance.
Turn the bottom part of the auxiliary handle 9 in rotation di-
rection  and push the auxiliary handle 9 forward until you
can pivot it to the desired position. Then pull the auxiliary han-
dle 9 back again and tighten it by turning the bottom part of
the auxiliary handle in rotation direction .
Adjusting the Drilling Depth (see figureA)
The required drilling depth X can be set with the depth stop
10.
Turn the bottom part of the auxiliary handle 9 in anticlockwise
direction and insert the depth stop 10.
Pull out the depth stop until the distance between the tip of
the drill bit and the tip of the depth stop corresponds with the
desired drilling depth X.
Rotary drill GBM 13-2 RE
Article number
3 601 ... ... AB2 002 ... AB2 000 ... AB2 001 ... AB2 030 ... AB2 060 ... AB2 070 ... AB2 040
Rated power input
W750750 750 750 750 710 750
Output power
W353353 353 353 374 365 353
No-load speed
–1st gear
–2nd gear
min
-1
min
-1
0–1000
0–3000
0–1000
0–3000
0–1000
0–3000
0–1000
0–3000
0–1000
0–3000
0–1000
0–3000
0–1000
0–3000
Rated speed
–1st gear
–2nd gear
min
-1
min
-1
500
1750
500
1750
500
1750
500
1750
500
1750
500
1750
500
1750
Rated torque
(1st/2nd gear)
Nm 6.8/2.5 6.8/2.5 6.8/2.5 6.8/2.5 6.5/2.2 6.5/2.2 6.8/2.5
Spindle collar dia.
mm 43 43 43 43 43 43 43
Speed preselection
 
Speed control
 
Right/left rotation
 
Overload Clutch
 
Keyless chuck with
securing ring
 ––––– 
Keyless Chuck
–  –  –
Key type drill chuck
– –  ––––
Maximum drilling diam-
eter (1st/2nd gear)
– Steel
– Wood
–Aluminium
mm
mm
mm
13/8
32/20
20/12
13/8
32/20
20/12
13/8
32/20
20/12
13/8
32/20
20/12
13/8
32/20
20/12
13/8
32/20
20/12
13/8
32/20
20/12
Chuck clamping range
mm 1 –13 1 –13 1 –13 1–13 1–13 1–13 1–13
Weight according to
EPTA-Procedure
01/2003
kg 2.4 2.4 2.4 2.4 2.4 2.4 2.4
Protection class
/II /II /II /II /II /II /II
Henk Becker
Executive Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
OBJ_BUCH-2291-004.book Page 14 Tuesday, June 23, 2015 11:54 AM