Bosch GBM 13-2 RE - Technical Data; Rotary Drill Specifications; Assembly; Auxiliary Handle Installation

14 | English
1 609 92A 4SD | (17.4.18)
Bosch Power Tools
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Technical Data
Assembly
Auxiliary Handle (see figure A)
 Operate your machine only with the auxiliary handle 9.
The auxiliary handle 9 can be set in 12 positions to achieve a
safe and low-fatigue working stance.
Turn the bottom part of the auxiliary handle 9 in rotation di-
rection  and push the auxiliary handle 9 forward until you
can pivot it to the desired position. Then pull the auxiliary han-
dle 9 back again and tighten it by turning the bottom part of
the auxiliary handle in rotation direction .
Adjusting the Drilling Depth (seefigure A)
The required drilling depth X can be set with the depth stop
10.
Turn the bottom part of the auxiliary handle 9 in anticlockwise
direction and insert the depth stop 10.
Pull out the depth stop until the distance between the tip of
the drill bit and the tip of the depth stop corresponds with the
desired drilling depth X.
Afterwards, tighten the bottom part of the auxiliary handle 9
again by turning in clockwise direction.
The knurled surface of the depth stop 10 must face upward.
Rotary drill GBM 13-2 RE
Article number
3 601 ... ... AB2 006 ... AB2 004 ... AB2 005 ... AB2 031 ... AB2 062 ... AB2 071 ... AB2 041
Rated power input
W750750 750 750 750 710 750
Output power
W353353 353 353 374 365 353
No-load speed
–1st gear
–2nd gear
min
-1
min
-1
0–1000
0–3000
0–1000
0–3000
0–1000
0–3000
0–1000
0–3000
0–1000
0–3000
0–1000
0–3000
0–1100
0–3400
Rated speed
–1st gear
–2nd gear
min
-1
min
-1
500
1750
500
1750
500
1750
500
1750
500
1750
500
1750
500
1750
Rated torque
(1st/2nd gear)
Nm 6.8/2.5 6.8/2.5 6.8/2.5 6.8/2.5 6.5/2.2 6.5/2.2 6.8/2.5
Spindle collar dia.
mm 43 43 43 43 43 43 43
Speed preselection
 
Speed control
 
Right/left rotation
 
Overload Clutch
 
Keyless chuck with
securing ring
 ––––– 
Keyless Chuck
–  –  –
Key type drill chuck
– –  ––––
Maximum drilling diam-
eter (1st/2nd gear)
– Steel
– Wood
–Aluminium
mm
mm
mm
13/8
32/20
20/12
13/8
32/20
20/12
13/8
32/20
20/12
13/8
32/20
20/12
13/8
32/20
20/12
13/8
32/20
20/12
13/8
32/20
20/12
Chuck clamping range
mm 1 –13 1–13 1–13 1–13 1–13 1–13 1–13
Weight according to
EPTA-Procedure
01:2014
kg 2.4 2.4 2.4 2.4 2.4 2.4 2.4
Protection class
/II /II /II /II /II /II /II
OBJ_BUCH-2291-005.book Page 14 Tuesday, April 17, 2018 3:39 PM