Bosch Greenstar combi 151 p - Maintenance; Inspection and Cleaning

26 | Notes on installation and operation
Greenstar combi 100 p / 151 p6720872361 (2017/04)
NOTICE:
Risk of damage to 2 inch PVC pipe
▶ For Greenstar combi 151 p, use 2 inch CPVC pipe or 3 inch pipe.
All PP/PVC/CPVC combustion air and vent pipe materials and fittings
(except for steel components) must satisfy the following requirements
and be UL-approved:
Table 11 Materials for pipe
For installations in Canada, field supplied plastic vent piping must
comply with CAN/CGA B149.1 (latest edition) and be certified to the
Standard for Type BH Gas Venting systems. ULC S636 components of
the listed system may not be combined with other venting systems or
pipes/fittings that are not listed here. All plastic components and
specified primers and glues of certified vent systems must be from a
single manufacturer and not intermingled with other system
manufacturer's vent system parts.The supplied vent connector and
separate available vent termination are certified as a part of the
Greenstar Boiler.
Table 12 Roof terminals
Table 13 Wall terminals
Material Item United states Canada
combi 100 p combi 151 p
PVC schedule 40, 80 2" (50 mm) Vent or air pipe and fitting ANSI/ASTM D1785 BH Gas venting systems,
ULC S636
a
,
Class IIA - PVC,
Class IIB - CPVC,
Class IIC - polypropylene
a. Components of the certified vent systems must not be interchanged with other vent systems or unlisted pipe fittings. Plastic components, and specified primers and glues
of the certified vent system must be from a single system manufacturer and not intermixed with other system manufacturer's vent system parts.
X
PVC-DWV ANSI/ASTM D2665 X
CPVC schedule 40, 80 ANSI/ASTM F441 X X
PVC schedule 40, 80 3" (76 mm) Vent or air pipe and fitting ANSI/ASTM D1785 X X
PVC-DWV ANSI/ASTM D2665 X X
CPVC schedule 40, 80 ANSI/ASTM F441 X X
PP 3" (80 mm) vent or air pipe M&G Duravent
PolyPro and Centrotherm InnoFlue
ANSI Cat IV
Approved Polypropylene
XX
PP 2" (50 mm) vent or air pipe M&G Duravent
PolyPro and Centrotherm InnoFlue
ANSI Cat IV
Approved Polypropylene
XX
PP 3"/5" (80/125 mm) concentric
(manufactured by M&G Duravent)
ANSI Cat IV
Approved Polypropylene
XX
PP-Flex 3" (80 mm) Vent and combustion air pipe ANSI Cat IV
Approved Polypropylene
XX
PP-Flex 2" (50 mm) vent or air pipe M&G Duravent
PolyPro and Centrotherm InnoFlue
ANSI Cat IV
Approved Polypropylene
X
PVC Pipe cement/primer ANSI/ASTM D2564 X X
CPVC ANSI/ASTM F493 X X
Terminal end, vertical Material Supplier Order number
Ø 3" / Ø 5" (Ø 76/125 mm) concentric PVC IPEX System 636 196006
Ø 3" / Ø 5" (Ø 76/125 mm) concentric CPVC IPEX System 636 197009
Ø 3" / Ø 5" (Ø 80/125 mm) concentric PP M&G Duravent PolyProCentrotherm InnoFlue 3PPS-VK
Ø 3" (80 mm) PolyPro Support ElbowBase Suport
+ SW to Flex Coupler
M&G Duravent PolyProCentrotherm InnoFlue 3PPS-FCT
Ø 2" (Ø 50 mm) PolyPro Support ElbowBase Suport
+ SW to Flex Coupler
M&G Duravent PolyProCentrotherm InnoFlue 2PPS-FCT
Wall termination Flue System / Materials Supplier Order number
Ø 3" (Ø 76 mm) parallel stainless steel Flex-L 46546901
90 °-elbow with
inlet screen
PVC (elbow)
stainless steel (screen)
IPEX (elbow)
Langly Wire (screen)
ULC S636 approval (elbow) L2594
(screen)
Ø 3" (Ø 76 mm) twin pipe termination PP M&G Duravent PolyPro 3PPS-HTP
Ø 3" (Ø 76 mm) single pipe termination PP M&G Duravent PolyPro 3PPS-HST
Ø 3" / Ø 5" (Ø 80/125 mm) Bosch Greenstar
Horizontal Telescopic Terminal Kit
PP Bosch 7738003218