Bosch GSB Professional Series - Declaration of Conformity; Technical Data

English | 15
Bosch Power Tools 2 609 932 948 | (13.1.16)
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-1.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
05.05.2014
Technical Data
Henk Becker
Executive Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Impact Drill GSB ... 21-2 21-2 RE 21-2 RE 21-2 RCT 21-2 RCT
Article number
3 601 ... A9C 0.. A9C 5.. A9C 6.. A9C 7.. A9C 8..
Rated power input
W11001100 1100 1300 1300
Output power
W630630 630 695 695
No-load speed
–1st gear
–2nd gear
min
-1
min
-1
900
3000
0 – 900
0 – 3000
0 – 900
0 – 3000
0–900
0–3000
0–900
0–3000
Rated speed
–1st gear
–2nd gear
min
-1
min
-1
580
1900
580
1900
580
1900
900
3000
900
3000
Impact frequency at no-load min
-1
51000 51000 51000 51000 51000
Rated torque (1st/2nd gear)
Nm 9.6/3.2 9.6/3.2 9.6/3.2 7.8/2.6 7.8/2.6
Electronic torque control
– ––
Speed preselection
– 
Constant electronic control
– ––
Right/left rotation
– 
Key type drill chuck
 –  – 
Keyless drill chuck
–  –  –
Fully automatic spindle locking (Auto-lock)
–  –  –
Safety Clutch
 
Spindle collar dia.
mm 43 43 43 43 43
Maximum drilling diameter (1st/2nd gear)
–Concrete
– Brickwork
– Steel
– Wood
mm
mm
mm
mm
22/13
24/16
16/8
40/25
22/13
24/16
16/8
40/25
22/13
24/16
16/8
40/25
22/13
24/16
16/10
40/25
22/13
24/16
16/10
40/25
Chuck clamping range
mm 3 – 16 1.5 – 13 1.5 – 13 1.5–13 1.5–13
Weight according to EPTA-Procedure
01/2003
kg 2.9 2.9 2.9 2.9 2.9
Protection class
/II /II /II /II /II
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
OBJ_BUCH-909-004.book Page 15 Wednesday, January 13, 2016 11:44 AM