ICP-CC408 | Installation Guide | 11.0 Dialer Information EN | 51
Bosch Security Systems, Inc. | 12/08 | F01U089463-02
11.6 Dialing Format
Location
080
1 Australian DTMF (5 digits/sec)
2 Australian decadic
3 Alternate DTMF and Australian decadic
4 International DTMF (touch tone)
5 Reversed decadic (10 minus 1)
6 Alternate DTMF and reversed decadic
The Dialing Format determines the method for
dialing telephone numbers. Options 3 and 6 alternate
the dialing sequence between DTMF and decadic if
the call to the base station receiver is unsuccessful.
Use caution when selecting the dialing method.
Select the Australian method only if the control panel
is connected to the Australian Telecommunications
Network. Select the International DTMF dialing
option only in countries that allow both the caller
and the receiver to terminate a phone call. Using the
incorrect format can disable the control panel’s
patented Telephone Anti-Jamming feature.
The alternating sequence is: DTMF –
decadic – DTMF – decadic – DTMF –
decadic.
11.7 Telco Arming Sequence
Location
113 to 142
Default
0
These locations allow you to activate call diversion
automatically on your telephone when you arm the
system in AWAY Mode.
When the Telco Arming Sequence is activated after
arming the system in AWAY Mode, the control
panel redirects all calls to your mobile phone, pocket
pager, or answering service.
Contact your telecommunications provider for more
information on Call Forward operations.
Table 49: Telco Arm/Disarm Dialing Digits
Digit
Required
Number to
Program
Digit
Required
Number to
Program
terminator 0 8 8
1 1 9 9
2 2 0 10
3 3 * 11
4 4 # 12
5 5 4 sec pause 13
6 6 break 14
7 7
To turn call forward (immediate) on, enter:
[* 2 1][forwarding telephone number][#]
Example
To immediately forward all incoming calls to the
telephone number 96721055 after arming the system
in AWAY Mode, program:
[11 2 1 9 6 7 2 1 10 5 5 12 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0]
To turn call forward (no answer) on, enter:
[* 6 1][forwarding telephone number][#]
Example
To forward all incoming calls, when there is no
answer, to the telephone number 96721055 after
arming the system in AWAY Mode, program:
[11 6 1 9 6 7 2 1 10 5 5 12 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0]
11.8 Telco Disarming Sequence
Location
143 to 158
Default
0
These locations allow you to deactivate call diversion
automatically on your telephone when you disarm
the system from AWAY Mode.
To turn call forward (immediate) off, enter:
[# 2 1 #]
Example
To disable call forward (immediate) after disarming
the system from AWAY Mode, program:
[12 2 1 12 0 0 0 0 0 0 0 0 0 0 0 0]
To turn call forward (no answer) off, enter:
[# 6 1 #]
Example
To disable call forward (no answer) after disarming
the system from AWAY Mode, program:
[12 6 1 12 0 0 0 0 0 0 0 0 0 0 0 0]
11.9 Call Back Telephone Number
Location
159 to 174
Default
0
This location stores the telephone number to call
when Upload/Download is requested or the user
holds down [6] to initiate a modem call from the
control panel to establish a communications link with
the remote computer. The computer must be running
the CC816 Alarm Link Software and must be set to
Waiting for an Incoming Call. The Call Back
Telephone Number is also required if Remote Connect
with Callback Verification is required (refer to Section
8.1.3 on page 42).
Refer to Section 8.0 Alarm Link Software on page 41
for more information.
To Next Page
Loading...
