Bosch Intellic EFAS-4.10 - Page 8

6.2.5 Conditions for switching-on and operating states ......................................................................................................................... 18
6.2.6 Changing the internal buer battery ..................................................................................................................................................18
6.2.6.1 Removing the internal buer battery .............................................................................................................................................18
6.2.6.2 Installing the battery .............................................................................................................................................................................19
6.2.7 Seals .................................................................................................................................................................................................................20
6.3 Preparation and conguration before activation of the control unit .......................................................................... 20
6.4 Activating the tachograph EFAS ......................................................................................................................................... 20
6.4.1 Sample printouts “Technical Data ......................................................................................................................................................... 23
6.4.1.1 Before activation .....................................................................................................................................................................................24
6.4.1.2 Activation...................................................................................................................................................................................................24
6.4.1.3 Initial Installation ....................................................................................................................................................................................25
6.4.1.4 Subsequent entry of the ocial number plate ............................................................................................................................26
6.4.1.5 Other calibration purpose ...................................................................................................................................................................26
6.5 Manual motion sensor pairing ............................................................................................................................................ 27
6.6 Installing the DSRC module ................................................................................................................................................. 28
6.6.1 Installation of the DSRC module according to EU regulation 2016/799 .................................................................................28
6.6.2 Connection of the DSRC module ..........................................................................................................................................................28
Chapter 7 General settings ............................................................................................................................. 29
7.1 Clock ......................................................................................................................................................................................... 29
7.1.1 Date and time ............................................................................................................................................................................................... 29
7.1.2 Time zone ......................................................................................................................................................................................................30
7.1.3 Daylight saving time ..................................................................................................................................................................................30
7.1.4 Date format ...................................................................................................................................................................................................30
7.2 Automatic activity setting after ignition OFF/ON............................................................................................................ 31
7.3 Blocking rst generation tachograph cards ..................................................................................................................... 31
7.4  Remote Data Downloading ......................................................................................................................................... 31
7.5 Fleet Management System FMS .......................................................................................................................................... 32
7.6 Removing the printer paper container and inserting the printer paper roll .............................................................. 32
Chapter 8 Parameter conguration .............................................................................................................. 33
8.1 Access rights ........................................................................................................................................................................... 33
8.2 Ranges of values and lengths .............................................................................................................................................. 33
8.3 Parameters for vehicle adaptation and for connecting external devices ................................................................... 33
8.3.1 Nominal voltage of the vehicle (on-board power supply) (RDI=0xFDA3) ..............................................................................34
8.3.2 CAN-bus conguration of the main CAN vehicle bus (CAN MAIN) ........................................................................................... 34
8.3.3 CAN-bus conguration of the auxiliary CAN expansion bus (CAN AUX) ................................................................................ 35
8.3.4 Wake-up via CAN-bus (RDI=0xFD6D) ..................................................................................................................................................35
8.3.5 Source to reset the trip distance motion sensor (RDI=0xFD00) .................................................................................................35
8.3.6 Source of lighting control (RDI=0xFD34) ...........................................................................................................................................35
8.3.7 Operating mode of the input A2 for lighting control (RDI=0xFDA1) ....................................................................................... 35
8.3.8 PWM conguration for lighting control..............................................................................................................................................35
8.3.9 Factor for calculating the speed of the output shaft (RDI=0xF91E) .........................................................................................35
8.3.10 Selection of engine-speed data source (RCI=0xFD3A) .................................................................................................................36
8.3.11 Engine speed factor (n-factor) (RDI=0xFD32) ...................................................................................................................................36
8.3.12 Conguration of the serial interface on D7 (RDI=0xFD26) ..........................................................................................................36
8.3.13 Conguration of the serial interface on D8 (RDI=0xFD26) ..........................................................................................................36
8.3.14 Monitoring of pulse output B7 (RDI=0xFD35)..................................................................................................................................36
8.3.15 Function of the pulse output D6 (RDI=0xFDA0) .............................................................................................................................. 36
8.3.16 CAN Heart beat monitoring of a connected bus subscriber (RDI=0xF90C) ..........................................................................36
8.3.17 Transmission interval of the TCO1 message (RDI=0xF920) .........................................................................................................36
8.3.18 Conguration of FMS service (RDI=0xFD9E) ..................................................................................................................................... 36
8.4 Automatic Parameters Detection ....................................................................................................................................... 37
Chapter 9 Calibration ...................................................................................................................................... 39
9.1 Conguration with factory settings ................................................................................................................................... 39
9.2 Preparatory actions ............................................................................................................................................................... 40
9.2.1 Visual inspection .........................................................................................................................................................................................40
9.2.2 Inspection of the seals and installation plaque ...............................................................................................................................40
9.2.3 Data read-out ...............................................................................................................................................................................................40
9.2.4 Check internal buer battery .................................................................................................................................................................40
9.3 Test equipment ....................................................................................................................................................................... 40
9.4 Calibrating the EFAS .............................................................................................................................................................. 40