Bosch PST - Page 15

English | 15
Jigsaw PST 750 PE PST 750 PEL PST 800 PEL
PST 8000 PEL
PST 8500 PEL
Stroke mm 20 20 20
Max. cutting depth
– in wood mm 75 75 80
– in aluminium mm 12 12 12
– in steel (unalloyed) mm 5 5 5
Max. cutting angle (left/right) ° 45 45 45
Weight according to EPTA-Procedure01:2014 kg 1.9 1.9 1.9
Protection class
/II /II /II
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Noise/Vibration Information
Noise emission values determined according to
EN62841‑2‑11.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 85dB(A); sound power level
96dB(A). Uncertainty K=5dB.
Wear hearing protection!
Vibration total values a
h
(triax vector sum) and uncertainty K
determined according to EN62841‑2‑11:
Cutting boards with saw bladeT144D:
a
h,B
= 13m/s
2
, K = 3m/s
2
,
cutting sheet metal with saw blade T118A:
a
h,M
= 7m/s
2
, K = 1.5m/s
2
.
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
u Pull the plug out of the socket before carrying out any
work on the power tool.
Inserting/changing the saw blade
u When fitting or changing the saw blade, wear protect-
ive gloves. Blades are sharp and can become hot when
used for prolonged periods of time.
Selecting the saw blade
You will find an overview of recommended saw blades at the
end of these operating instructions. Only use saw blades
with a single lug shank (T shank) or with a 1/4" universal
shank (U shank). The saw blade should not be longer than
required for the intended cut.
Use a narrow saw blade when sawing tight curves.
Inserting the saw blade (seefigure A)
u Clean the shaft on the saw blade before inserting it.
Adirty shaft cannot be securely fixed in place.
PST 800 PEL/PST 8000 PEL/PST 8500 PEL: Remove the
hood (10) if required.
Push the saw blade receptacle (14) upwards in the direction
of the arrow. Push the saw blade (16), with the teeth in the
cutting direction, into the saw blade receptacle as far as it
will go.
Make sure when inserting the saw blade that the back of the
saw blade is in the groove on the guide roller (15).
u Check that the saw blade is seated securely. A loose
saw blade can fall out and lead to injuries.
Removing the Saw Blade (seefigureB)
Push the saw blade receptacle (14) upwards in the direction
of the arrow and remove the saw blade (16).
If the saw blade jams during removal, set the adjusting
lever(8) to maximum pendulum action and press the saw
blade receptacle (14) slightly forward (max. 2mm).
Saw Blade Storage Compartment (see figureC)
(PST800PEL/PST8000PEL/PST8500PEL)
You can keep up to six saw blades that are no longer than
110mm in the saw blade storage compartment (6). Insert
the saw blades with single lug shank (T shank) into the saw
blade storage compartment in the recess intended for these.
You can place up to three saw blades on top of each other.
Close the saw blade storage compartment and push it as far
as it will go into the recess in the base plate (7).
Bosch Power Tools 1 609 92A 67V | (18.01.2021)