Bosch Solution 16i - Page 114

10-2
Bosch Security Systems 09/11 BLCC500I
Solution 16i  Installation Manual  Device Programming
3) Use the ON and OFF keys to toggle LAN secure on
or o.
4) Press [OK] to exit.
K EYPA D OP TIO NS
Devices > Keypads > cP-VOl
Keypad Volume

-

MENU 6-1-0
This menu allows you to adjust the volume of the keypad’s
buzzer. Each keypad can have their volume adjusted
separately to suit your needs.
1) Enter your Installer PIN or Master PIN + [MENU].
2) Enter [6] + [1] + [0] + [OK].
The keypad will display the current volume setting
and the keypad address. This example shows keypad
1.
vol =6
1
3) Press the the [↑] and [↓] keys to adjust the volume.
Min = 1, Max = 8 , 0 = O.
4) Press [OK] to save and exit, or press [MENU] to exit
without saving.
Devices > Keypads > cP-cOn
Keypad Contrast

-

MENU 6-1-1
This menu allows you to adjust the contrast of the keypad’s
LCD display to improve visability. Each keypad can have
their display adjusted separately.
1) Enter your Installer PIN or Master PIN + [MENU].
2) Enter [6] + [1] + [1] + [OK].
The keypad will then display the contrast screen which
includes all of the available symbols and the current
contrast setting.
POWER
FIRE

ALARM
!
SERVICE
M
PART
OFF ON
9
10 11 12 13 14 15 16
1 2 3 4 5 6 7 8
(
(
)
)
CHIME
PHONE
AREA
3) Press the the [↑] and [↓] keys to adjust the contrast.
Min = 1, Max = 3.
4) Press [OK] to save and exit, or press [MENU] to exit
without saving.
Devices > Keypads > cP-bl
Keypad Backlight

-

MENU 6-1-2
This menu allows you to adjust the brightness of the
keypad’s LCD display backlight. Each keypad can have
their display adjusted separately.
1) Enter your Installer PIN or Master PIN + [MENU].
2) Enter [6] + [1] + [2] + [OK].
The keypad displays the current backlight setting and
the keypad address. This example shows keypad 1.
bl =8
1
3) Press the the [↑] and [↓] keys to adjust the contrast.
Min = 1, Max = 10, 0 = O.
4) Press [OK] to save and exit, or press [MENU] to exit
without saving.
Devices > Keypads > L613
Home Area

MENU 6-1-3
0 1
00 = No Home Area
01 = Area 1 03 = Area 3
02 = Area 2 04 = Area 4
This menu allows you to assign each keypad to a default
home area (Area 1 to 4). Only 1 home area can be
programmed for each keypad.
If a user toggles the keypad display to view a dierent
area, the keypad will automatically timeout and move
back to the home area if no key is pressed for a period of
60 seconds.
To prevent users from viewing areas which they do
not have access to, you will need to enable the PIN
To Change Area option. Setting this option will set
the system to request a user’s PIN before allowing
them to view another area. The system will only
allow a user to view the areas they have access to.
See MENU 6-1-4 — Keypad General Options.
1) Enter your Installer PIN + [MENU].
2) Enter [6] + [1] + [3] + [OK], then enter the number of
the keypad that you want to change and press [OK].
3) Enter the Home Area required, then press [OK] to
save and exit or press [MENU] to exit without
saving.
d =1