10-6
Bosch Security Systems 09/11 BLCC500I
Solution 16i
Installation Manual Device Programming
Devices > Keypads > L618
Lockout Time
MENU 6-1-8
(*** System Wide Parameter ***)
0 6 0
SECONDS
This menu programs how long a keypad will be
quarantined if the PIN retry count value is exceeded.
See MENU 1-5-1 — PIN Retry Count. The PIN retry counter is
reset when any area is armed or disarmed using a valid PIN.
1) Enter your Installer PIN + [MENU].
2) Enter [6] + [1] + [8] + [OK]. The keypad will display
the current keypad lockout time.
d= 060
3) Use the numeric keys to program the number of
seconds the keypad will be locked out for. Valid
entries are 0 - 255, 0 = No Lockout.
4) Press [OK] to save and exit, else press [MENU] to
exit without saving.
R F RE CEI VE R OP TI ON S
Devices > RF Devices > L620
Receiver Options
MENU 6-2-0
1 Display RF Receiver Trouble Y
2 Alarm On RF Receiver Tamper Y
3 Report RF Receiver Tamper Y
4 Alarm On RF Receiver Jam Detect N
5 Report RF Receiver Jam Detect N
6 Alarm On RF Receiver Comms Fail Y
7 Report RF Receiver Comms Fail Y
8 Reserved N
This menu option allows you to congure the various RF
receiver functions. Only one RF reciever can be tted per
panel.
1) Enter your Installer PIN + [MENU].
2) Enter [6] + [2] + [0] + [OK].
The keypad will display the current options which are
selected or enabled.
-bit-
1 2 3 6 7
3) Use the numeric keys [1] to [8] to turn on and o
the features as required. When the corresponding
number on the keypad is on then the option is
selected.
4) When all options are programmed, press [OK] to
save and exit, or press [MENU] to exit without
saving.
Display RF Receiver Trouble
Setting this option allows the panel to display a trouble
condition on the keypad when an RF receiver fail
condition occurs.
Alarm On RF Receiver Tamper
Setting this option allows the panel to trigger an alarm
when the RF receiver tamper circuit is tripped.
Report Faulted RF Receiver Tamper
Setting this option allows the panel to send an RF
Receiver Tamper report to the the base station when the
RF receiver tamper circuit is tripped. A restore report will
be sent when the tamper circuit is resealled.
Alarm On RF Receiver Jam Detect
Setting this option allows the panel to sound an
alarm when the RF Receiver detects a jamming signal.
This signal may not be provided by all compatible RF
Receivers.
Report Receiver Jam Detect
Setting this option allows the panel to send an RF
Receiver Jam report to the base station when the RF
Receiver detects a jamming signal. A restore report will
be sent as soon as the jamming signal stops.
Alarm On RF Receiver Comms Fail
Setting this option allows the panel to sound an alarm
when it is unable to communicate with the RF Receiver.
Report RF Receiver Comms Fail
Setting this option allows the panel to send an RF
Receiver Comms Fail report to the base station when the
panel is unable to communicate with the RF Receiver. A
restore report will be sent as soon as communication is
restored between the panel and the RF receiver.
Device > RF Devices > L621
Supervision Time
MENU 6-2-1
(*** System Wide Parameter ***)
0 2 4
HOURS
This menu sets the global RF supervision time for all RF
devices connected to the system.
RF transmitters (sensor devices) will send a supervisory
test signal approximately once every hour. The RF receiver
expects to receive this supervisory signal from every
transmitting device within the supervision time period.
The panel will send a Missing report to the base station for
any RF device that fails to report within the supervision
time.
To Next Page
Loading...
