How to unlock my Braun 9090cc?
If your Braun shaver doesn't start, the travel lock may be activated. To unlock it, press and hold the on/off switch for 3 seconds. Also, if you have a wet&dry model (9095cc w&d/9093s w&d/ 9080cc w&d/9040s w&d), ensure it is unplugged, as it can only be operated cordlessly.
What to do if my Braun Shaver is not charging?
If your Braun shaver isn't charging, make sure it's properly placed in the Clean&Charge Station, aligning the contacts. Charging can sometimes be delayed, especially after long storage, so wait a few minutes. Ensure the ambient temperature is between 5 °C and 35 °C. Also, verify the special cord set is correctly plugged in and snapped into place.
How to improve shaving performance of Braun 9090cc Shaver?
If your Braun shaver's performance has declined, the shaving system might be clogged. Soak the Foil & Cutter cassette in hot water with a drop of dish liquid, then rinse and tap it out. After drying, apply a drop of light machine oil on the foil. Also, the Foil & Cutter cassette may be worn and need replacement.
Why has my Braun 9090cc battery performance dropped?
A drop in your Braun shaver's battery performance may be due to regularly cleaning the shaver head with water but not lubricating it. Apply a drop of light machine oil on top of the foil once a week for lubrication. Another cause could be worn Foil & Cutter cassette, which requires more power; consider replacing it.
Why does my Braun 9090cc Shaver not charge completely?
If your Braun shaver doesn't charge completely and keeps blinking, the ambient temperature may be out of the recommended range. Ensure the temperature is between 5 °C and 35 °C for charging.
How to get rid of the smell from my Braun 9090cc head?
An unpleasant smell from your Braun shaver head can occur if you clean it with water. Use only hot water and, occasionally, a bit of liquid soap (without abrasive substances). Remove the Foil & Cutter cassette to let it dry. Also, if the cleaning cartridge has been in use for more than 8 weeks, replace it.
Why does my Braun 9090cc turn off with a full battery?
If your Braun shaver turns off despite a full charge, it could be due to worn foil and cutter requiring more power than the motor can provide; replace the Foil & Cutter cassette. Also, regularly oil the shaving system, especially if you clean it with water only.
What to do if cleaning doesn't start on my Braun Clean&Charge Station?
If cleaning doesn't start when you press the start button on your Braun Clean&Charge Station, ensure the shaver is correctly placed with the contacts aligned. Check if the cleaning cartridge has enough fluid; a blinking red indicator means you need a new cartridge. Also, the appliance may be in stand-by mode, so press the start button again.
Why is my Braun 9090cc head damp?
If your Braun shaver head is damp, the drain of the Clean&Charge Station might be clogged; clean it with a wooden toothpick. Alternatively, if the cleaning cartridge has been used for a while, the alcohol proportion decreases while the oil proportion increases; remove residue with a cloth.
Defines content posing risk of death or serious injury.
Defines content posing risk of injury or material damage.
Important safety precautions regarding charging plug and electrical safety.
Safety instruction for safely unplugging the power cord.
Safety warnings concerning the system's components and cleaning fluid.
Steps to set up the Clean&Rinse station and install the cleaning cartridge.
How to charge the shaver using the Clean&Rinse station.
Steps for initiating and executing the automatic cleaning process.
Solves common shaver problems like failure to start or charge.
Solves problems where the cleaning process does not initiate.
Details on warranty terms, coverage, and proper handling of the warranty card.
Instructions on how to request repair services for the product.
Contact details for customer inquiries and after-sales support.
To Next Page
General