Broadcom Brocade X7-4 Director

To Next Page

To Previous Page

X7-4-Install-IG100 Installation Guide

Brocade

X7-4 Director Hardware Installation Guide

2. Align the six ball stud attachment holes in the back of the door with the six ball studs in the chassis and push the door

into place. It will snap onto the studs.

Figure 81: Installing Chassis Door

X7-4-Install-IG100

189

Broadcom

Main Page

Default Chapter2
- Table of Contents2
Copyright Notice9
Introduction10
- About this Document10
- Supported Hardware10
- Notes, Cautions, and Danger Notices12
- Contacting Technical Support for Your Brocade ® Product12
- Document Feedback13
Device Overview14
- Product Features14
- Hardware Components15
- Port-Side View of the Device16
- Port-Side Slot Numbering17
- Nonport-Side View of the Device17
Preparing for Installation19
- Safety Precautions19
- Facility Requirements21
- Time and Items Required21
- Shipped Items23
- Quick Installation Checklists24
Mounting the Device27
- Mounting Options27
- Mounting Precautions27
- Unpacking and Transporting the Device28
- Installing the 8U Chassis Airflow Diversion or Port-Side Exhaust Kit for Four-Post Racks (XBR-DCX4S-0121 and XBR-DCX4S-0130)28
- Installing the 8U Chassis MID-Mount Rack Kit for Two-Post Racks (XBR-DCX4S-0126 and XBR-X64-0126)43
- Installing the 8U Chassis 27-31-Inch Rail Rack Kit for Four-Post Racks (XBR-DCX4S-0120)51
Initial Setup and Verification56
- Configuration and Verification Task Guide56
- Items Required57
- Providing Power to the Device57
  - Connecting the Power Cord to AC Power Supplies58
  - Connecting to HVAC/HVDC Power Supplies58
    - Using HVAC/HVDC Power Cords61
- Establishing a Serial Connection to the Device62
- Configuring the IP Addresses64
- Establishing an Ethernet Connection to the Device65
- Setting the Domain ID66
- Setting the Date and Time66
  - Setting the Time Zone67
  - Synchronizing the Local Time with an External Source68
- Customizing the Chassis and Switch Name68
- Verifying Installed Licenses and the License Key69
- Verifying Correct Operation70
- Backing up the Configuration70
- Powering down the Chassis71
Installing Transceivers and Cables74
- Supported Transceivers and Cables74
  - Port and Extension Blade Transceivers76
  - Core Routing Blades77
- Time and Items Required79
- Precautions Specific to Transceivers and Cables79
- Cleaning the Fiber-Optic Connectors80
- Cable Management80
- Installing an SFP+ Transceiver80
- Replacing an SFP+ Transceiver82
- Installing a QSFP Transceiver83
- Replacing a QSFP Transceiver84
- Verifying the Operation of New Transceivers85
Monitoring the Device86
- Introduction86
- Interpreting FC32-X7-48 Port Blade Leds86
- Interpreting FC64-48 Port Blade Leds88
- Interpreting FC32-64 Port Blade Leds90
- Interpreting Extension Blade Leds92
- Interpreting Control Processor Blade Leds94
- Interpreting Core Routing Blade Leds96
- Interpreting WWN Card Leds97
- Interpreting Power Supply Leds98
- Interpreting Fan Assembly Leds101
- Interpreting POST and Boot Results102
- Using Monitoring Commands103
- Running Diagnostic Tests118
Port and Extension Blades119
- FC32-X7-48 Port Blade Overview119
  - FC32-X7-48 Port Blade Numbering and Trunking119
- FC64-48 Port Blade Overview120
  - FC64-48 Port Blade Numbering and Trunking121
- FC32-64 Port Blade Overview122
  - FC32-64 Port Blade Numbering and Trunking122
- Extension Blade Overview123
  - Extension Features124
  - SX6 Blade Port Numbering and Trunking125
- Blade-Specific Precautions126
- Faulty Blade Indicators126
- Time and Items Required for Removal and Installation127
- Removing a Blade127
- Installing a Blade129
- Verifying Blade Operation130
Core Routing Blades131
- Core Routing Blade Overview131
- Blade-Specific Precautions135
- Faulty Core Routing Blade Indicators136
- Time and Items Required136
- Replacing a Core Routing Blade137
- Verifying Blade Operation140
Control Processor Blades141
- Control Processor Blade Overview141
  - CPX7 Port Identification141
- Blade-Specific Precautions142
- Blade Fault Indicators143
- Blade Replacement Task Guide143
- Time and Items Required for Replacement144
- Preparing for Replacement144
- Replacing a CP Blade145
- Verifying Blade Operation154
WWN Cards155
- WWN Card Overview155
  - WWN Card Location and Numbering155
- Precautions Specific to WWN Cards156
- WWN Card Fault Indicators156
- WWN Card Replacement Task Guide158
- Time and Items Required for Replacement158
- Using the Wwnrecover Utility158
- Preparing for WWN Card Replacement160
- Hot-Swap Replacement161
- Cold-Swap Replacement162
- Removing the WWN Card and Bezel164
- Configuring the Airflow Direction on WWN Cards165
- Verifying WWN Card Operation165
Power Supply Assemblies166
- AC Power Supply Overview166
- HVAC/HVDC Power Supply Overview167
- Power Supply Assembly Numbering168
- Fan and Power Supply Airflow168
- Precautions Specific to Power Supply Assembly170
- Power Supply Assembly Fault Indicators170
- Power Supply Assembly Task Guide170
- Time and Items Required171
- Removing a Power Supply172
- Installing a Power Supply173
- Verifying Power Supply Operation174
Fan Assemblies175
- Fan Assembly Overview175
  - Fan and Power Supply Airflow175
  - Fan Assembly Numbering176
- Precautions Specific to Fan Assemblies177
- Fan Assembly Fault Indicators177
- Fan Assembly Task Guide178
- Time and Items Required179
- Removing a Fan Assembly179
- Installing a Fan Assembly180
- Verifying Fan Operation180
Blade Filler Panels181
- Blade Filler Panel Removal and Replacement181
- Removing a Filler Panel181
- Installing a Filler Panel182
Cable Management Fingers184
- Cable Management Fingers Overview184
- Time and Items Required for Removal and Replacement184
- Removing the Cable Management Finger Assembly184
- Installing the Cable Management Finger Assembly185
Chassis Door187
- Chassis Door Overview187
- Time and Items Required187
- Removing a Chassis Door187
- Installing a Chassis Door188
Replacing the Chassis190
- Chassis Replacement Overview190
- Precautions Specific to Chassis Replacement190
- Chassis Replacement Task Guide190
- Chassis Fault Indicators191
- Time and Items Required191
- Preparing for Replacement192
  - Recording Critical Device and SAN Information192
  - Disconnecting from the Network and Fabric196
- Removing Components from the Chassis196
- Installing the Replacement Chassis197
- Installing Components into the Chassis197
- Synchronizing Airflow Direction on WWN Cards198
- Downloading the Configuration199
- Reconnecting the System to the Network and Fabric199
- Verifying Correct Operation of the System200
- Verifying Correct Configuration of the Fabric201
Regulatory Statements203
- BSMI Statement (Taiwan)203
- Canadian Requirements203
- CE Statement203
- China ROHS203
- FCC Warning (U.S. Only)203
- KCC Statement (Republic of Korea)204
- VCCI Statement204
Cautions and Danger Notices205
- Cautions205
- Danger Notices210
Revision History214

Broadcom Brocade X7-4 Director - Page 189

Table of Contents