3. Warning labels
146
2
357
<When you dispose of the machine>
Required Tools
Phillips screwdriver: M3 to M5
Disassembling
1) Remove the Cover of BACK SIDE bottom center.
2) Remove the Lithium Battery (1) by pulling out the holder
in the direction of the arrow.
3) Pickup the Lithium Battery (1) to the direction of the arrow.
Checking the installation site
The following environmental requirements should be met:
Environment Temperature Humidity
Humidity (%)
0°C (32°F) to
40°C (104°F)
20 % to 85 %
(no condensation)
Working
Environment
*1
10°C (50°F) to
35°C (95°F)
Recommended
Print Environment
*2
18°C (64.4°F) to
30°C (86°F)
35% to 85 %
(no condensation)
Electrical
Requirements
Power
Power
Consumptions
―
Single-phase
200-240 V,
50/60 Hz
5 A max.
*
1
: Environmental range where the printer can be operated.
*
2
: Environmental range where sufficient printing quality can
be secured.
When installing the printer, avoid any place that presents direct sunlight or a large amount of dust.
The size is 73.6 in. (width) x 75.6 in. (depth) x 57.5 in. (height) (187 cm (width) x 192 cm (depth) x 146 cm (height)). The
main unit weighs 730 kg (1609 lb).
Do not use an extension cable.
Keep a minimum workspace of 31.5 in. (80 cm) in front and on the left and right sides of the printer. Also, keep 15.7 in. (40
cm) or wider clearance at the back of the printer. Keep 17.7 in. (45 cm) or wider space free above the unit as well. If this
space is not secured, you will have to move peripherals or the printer when making a repair.
When installing the printer, place a level gage on the top surface of the platen to make adjustments so that the main unit is
set horizontally.
Transporting the printer
CAUTION
The printer has a dimension of 73.6 in. (width) × 75.6 in.
(depth) × 57.5 in. (height) (187 cm (width) × 192 cm
(depth) × 146 cm (height)). The main unit weighs 730 kg
(1609 lb). Transporting and setting up of the printer
should be held by at least three persons in the proper
way. Otherwise, the printer may topple over and cause
injury.
During transportation, be careful not to get your feet
caught in the frame, casters, or adjusters under the
printer. Also, check the forward direction and be careful
not to get caught between obstacles and this printer.
Otherwise, the operator may get injured.
Refilling the ink and cleaning solution
Turn ON the power of the printer and perform the operation
while the printer is in Standby mode.
CAUTION
Be sure to wear a pair of plastic gloves and protective
glasses while refilling the ink.
IMPORTANT
Agitate the white ink before refilling.
For details, refer to the Instruction Manual.
1) -> [Ink refill] -> Select the ink color and cleaning
solution you want to refill ->
2) Insert the IC stick of the same color as the ink to refill ->
3) Refill the ink and cleaning solution.
IMPORTANT
When refilling ink or cleaning solution,
make sure the surface of the ink or
cleaning solution does not exceed the
scale line above 6. For white ink or
cleaning solution, refill it until the surface
exceeds the scale line below 6. For color
ink, refill it until the surface exceeds the
scale line below 4.
4) Follow the instructions on the screen.
IMPORTANT
Be sure to close the tank lids once you
have refilled the ink and cleaning solution.
To store a cock after use, wipe off ink with
a waste cloth and seal it in a plastic bag.
Do not use a non-standard funnel. Use
the provided cock. Otherwise, ink may be
contaminated or deteriorated, possibly
damaging the printer.
Maintenance list
To maintain the printing quality and use the printer for a longer time, the following maintenance is needed.
For details, refer to the Instruction Manual.
Maintenance timing Description
Error /
Warning display
Before printing Print out of the nozzle check pattern (checking on the print heads) ―
When an error /
warning is displayed
Confirmation and disposal of waste ink ○
Confirmation and disposal of waste water ○
Refilling the ink ○
Refilling the cleaning solution ○
Cleaning the nozzle guard and suction cap ○
Replacing the wiper, flushing foam, cap foam, and carriage foam ○
Replacing the mist fan filter ○
When the printer
becomes dirty
Head cleaning ―
White ink circulation ―
Cleaning the internal area of printer ―
Replacing the platen sheet ―
6
6
6
3
5
4
2
1
6
6
7
6
66
2
X1057
X1016
X1054
X1034
X1035
1
2
3
Waste ink tank Ink bottle
9 L
Waste water
tank
Pretreatment
5 kg (11 lb)
Pretreatment
20 kg (44 lb)
Ink bottle
18 L
Cleaning solution bottle
9 L
Cleaning solution bottle
18 L
Pretreatment
200 kg (440 lb)
PS
116.5 in. (296 cm)
or more
31.5 in. (80 cm)
or more
31.5 in. (80 cm)
or more
129.5 in. (329 cm)
or more
15.7 in. (40 cm)
or more
31.5 in. (80 cm)
or more
17.7 in. (45 cm) or more
There is a label on the back of the
printer that indicates the insertion slot.
(1)
(1)
GT60NB
SC5083-101 EN
2022.01.F(1)
https://www.brother.com/
1-5, Kitajizoyama, Noda-cho, Kariya 448-0803, Japan.
© 2021-2022 Brother Industries, Ltd. All Rights Reserved.
*Please note that the contents of this manual may differ slightly from the actual product purchased as a result of product
improvements.
This is the original instructions.
This product contains a CR Coin Lithium Battery
which contains Perchlorate Material – special
handling may apply.
See
http://www.dtsc.ca.gov/hazardouswaste/perchlorate.
Note based on California law (USA) on the
use and handling of Perchlorate
To Previous Page
Loading...
