- 18 -
D = touche DEUXIEME VITESSE
E = touche TROISIEME VITESSE
F = touche MINUTEUR ARRET AUTOMATIQUE 15
minutes (*)
Si votre appareil est équipé de la fonction vitesse
INTENSIVE, en partant de la TROISIEME vitesse et en
maintenant appuyée la touche E pendant environ 2
secondes, cette vitesse sera activée pendant 6 minutes
après lesquelles l’appareil se remettra à la vitesse pré-
cédemment configurée.
Quand la fonction est activée, la LED clignote.
Pour interrompre cette vitesse avant les 6 minutes
appuyer sur la touche E.
Pour certains modèles on peut même activer la fonc-
tion avec la première et la deuxième vitesse.
En appuyant sur le bouton F pendant 2 secondes
(lorsque la hotte est allumée), la fonction «clean air»
s’active. Cette fonction démarre le moteur pour 10
minutes par heure à la première vitesse. Dès que la
fonction est activée, le moteur démarre en 1
ère
vitesse
pour 10 minutes pendant lesquelles les boutons F et C
doivent clignoter en même temps. A la fin de ce temps,
le moteur s’arrête et la diode électroluminescente du
bouton F reste allumée sans clignoter jusqu’à ce que
le moteur reparte en 1
ère
vitesse 50 minutes plus tard.
Les diodes électroluminescentes F et C recommencent
à clignoter pendant 10 minutes et ainsi de suite. En
appuyant sur n’importe quelle touche à l’exception
des touches de lumière, la hotte retourne immédiate-
ment à son fonctionnement normal (ex. en appuyant
sur le bouton D la fonction «clean air» se désactive
et le moteur passe directement à la 2
ème
vitesse; en
appuyant sur le bouton B la fonction se désactive).
(*)La fonction “MINUTER ARRÊT AUTOMATIQUE”
retarde l’arrêt de la hotte, qui continuera de fonctionner
à la vitesse de service en cours au moment de l’activa-
tion de cette fonction, pendant 15 minutes.
•SaturationfiltresAnti-graisse/Charbonactif:
- Lorsque la touche A clignote avec une fréquence de
2 secondes, les filtres anti-graisse doivent être lavés.
- Lorsque la touche A clignote avec une fréquence de
0,5seconde, les filtres à charbon actif doivent être
remplacés ou nettoyés selon le type de filtre.
Lorsque les filtres nettoyés sont remis en place, réini-
tialisation la mémoire électronique en appuyant sur
la touche A pendant environ 5 secondes jusqu’à ce
qu’elle arrête de clignoter.
NOUS DECLINOS TOUTE RESPONSABILI TE POUR
LES EVENTUELS DÉGATS PROVOQUÉS PAR L’INOB-
SERVATION DES SUSDITES INSTRUCTIONS.
ENGLISH
GB
GENERAL
Carefully read the following important information
regarding installation safety and maintenance. Keep
this information booklet accessible for further con-
sultations. The appliance has been designed for use in
the ducting version (air exhaust to the outside - Fig. 6),
filtering version (air circulation on the inside - Fig. 7) or
with external motor.
SAFETY PRECAUTION
1. Take care when the cooker
hood is operating simultaneously
with an open fireplace or burner
that depend on the air in the
environment and are supplied
by other than electrical energy,
as the cooker hood removes the
air from the environment which
a burner or fireplace need for
combustion. The negative pres-
sure in the environment must not
exceed 4Pa (4x10-5 bar). Provide
adequate ventilation in the envi-
ronment for a safe operation of
the cooker hood. Follow the local
laws applicable for external air
evacuation.
Before connecting the model to
the electricity network:
- Control the data plate (posi-
tioned inside the appliance) to
ascertain that the voltage and
power correspond to the network
and the socket is suitable. If in
doubt ask a qualified electrician.
- If the power supply cable is dam-
aged, it must be replaced with
another cable or a special assem-
bly, which may be obtained direct
from the manufacturer or from
the Technical Assistance Centre.
2. Warning!
In certain circumstances electri-
cal appliances may be a danger
hazard.
A) Do not check the status of
the filters while the cooker
hood is operating.
B) Do not touch bulbs or adja-
cent areas, during or straight
after prolonged use of the
lighting installation.
C) Flambè cooking is prohibited
underneath the cooker hood.
D) Avoid free flame, as it is
damaging for the filters and a