The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
Pag.
1.0 11/2007 © CAME cancelli automatici s.p.a.
ENGLISH
Adjustment Trimmer
G
Trimmer ACT Adjusts the waiting time when gate is open. Once this time has elapsed, the gate closes automa-
tically. The waiting time can be adjusted anywhere between 1 and 150 seconds.
Trimmer DELAY 2M Adjusts the waiting time of the second motor during each closing run. The waiting time can be
adjusted anywhere between 1 and 16 seconds.
Trimmer -- SENS -- RUN Adjusts the amperometric sensibility which controls the power developed by the motor during
motion; if the power exceeds the adjusted level, the system sets in motion to invert the direction
of motion.
Trimmer -- SENS -- SLOWING Adjusts the amperometric sensibility which controls the power developed by the motor during
slowing downs; if the power exceeds the adjusted level, the system sets in motion to invert the
direction of motion.
Trimmer -- SPEED -- RUN
Adjusts the gate-leaf running speed when opening or closing.
Trimmer -- SPEED -- SLOWING Adjusts the gate leaf’s slowing speed at the end of the stroke when opening and closing.
1 OFF Enables the obstacle stand-by or partial stop function; connect the safety device to terminals [2-CY]. If device is unused, set
the DIP switch to ON;
1 OFF - 2 ON Obstacle stand-by – stops the gate when there is an obstacle is detected by the safety device; once the obstacle has
been cleared, the gate is automatically set back in motion to finish initial run. Connect the safety devices to terminal
[2-CY];
1 OFF - 2 OFF Partial stop – stops gate when an obstacle is detected by the safety devices; once the obstacle is cleared, the gate
remains still or closes if the automatic closing function is enabled. Connect the safety devices to terminal [2-CY];
Function Selection
F
The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
Pag.
1.0 11/2007 © CAME cancelli automatici s.p.a.
ENGLISH
Adjustment Trimmer
G
Trimmer ACT Adjusts the waiting time when gate is open. Once this time has elapsed, the gate closes automa-
tically. The waiting time can be adjusted anywhere between 1 and 150 seconds.
Trimmer DELAY 2M Adjusts the waiting time of the second motor during each closing run. The waiting time can be
adjusted anywhere between 1 and 16 seconds.
Trimmer -- SENS -- RUN Adjusts the amperometric sensibility which controls the power developed by the motor during
motion; if the power exceeds the adjusted level, the system sets in motion to invert the direction
of motion.
Trimmer -- SENS -- SLOWING Adjusts the amperometric sensibility which controls the power developed by the motor during
slowing downs; if the power exceeds the adjusted level, the system sets in motion to invert the
direction of motion.
Trimmer -- SPEED -- RUN
Adjusts the gate-leaf running speed when opening or closing.
Trimmer -- SPEED -- SLOWING Adjusts the gate leaf’s slowing speed at the end of the stroke when opening and closing.
1 OFF Enables the obstacle stand-by or partial stop function; connect the safety device to terminals [2-CY]. If device is unused, set
the DIP switch to ON;
1 OFF - 2 ON Obstacle stand-by – stops the gate when there is an obstacle is detected by the safety device; once the obstacle has
been cleared, the gate is automatically set back in motion to finish initial run. Connect the safety devices to terminal
[2-CY];
1 OFF - 2 OFF Partial stop – stops gate when an obstacle is detected by the safety devices; once the obstacle is cleared, the gate
remains still or closes if the automatic closing function is enabled. Connect the safety devices to terminal [2-CY];
Function Selection
F
To Next Page
Loading...
