Can-Am Spyder ST Limited SE5 User Manual

ROADSTER
PREDELIVERY
Bulletin
October 09, 2013 Subject:Can-Am™ Spyder™ ST Predelivery
Inspection
No. 2014-3
YEAR MODEL MODEL NUMBER SERIAL NUMBE
R
2014
Spyder ST Series
Refer to table on next
pages for co
mplete listing
All
TABLE OF CONTENTS
Page Page
IMPORTANT NOTICE ....................... 2
UPDATE SUMMARY........................ 3
MODEL LIST
ING............................. 4
UNCRATING .................................. 5
Crate Cover Removal .......................... 5
Parts and Sub-crate Removal ................. 5
Parts Chec
k...................................... 7
Lifting the Front of Vehicle ................... 7
Front Wheels Installation ...................... 9
Vehicle Re
moval ................................ 10
PARTS TO BE INSTALLED................. 11
Front Carg
o Module............................ 11
Battery ........................................... 16
AAPTS (Ambient Air Pressure and Temperature
Sensor) Installation ............................. 17
Low Beam He
adlight Connection ............ 18
Horn Connection................................ 18
Latch Release Cable, Front Storage
Compartment Cover ........................... 18
Diagnostic
Link Cable (DLC) .................. 19
Body Parts Installation ......................... 19
Front Fenders ................................... 20
Windshield
....................................... 22
Rear Fender ..................................... 23
Antenna (LTD Model Only) .................... 25
Hang Tag and
Safety Labels .................. 25
Licence Plate Installation ...................... 26
Accessories Installation........................ 26
Vehicle Deca
ls................................... 26
FLUIDS......................................... 26
General Guidelines ............................. 26
Fuel ............................................... 26
Clutch Flu
id (SM5 Model) ..................... 27
Engine Coolant.................................. 28
Coolant Level Verification ..................... 28
Brake Flui
d....................................... 29
Engine Oil........................................ 30
SETUP ......................................... 32
Guidelines ....................................... 32
Tire Pressure .................................... 32
Drive Belt ........................................ 3
2
Clutch Lever..................................... 34
Lights............................................. 34
B.U.D.S. Pr
ogramming......................... 36
Clock and Language Setting .................. 38
ASSEMBLY INSPECTION .................. 39
FINAL INSPEC TION ......................... 39
Vehicle Tes
t Run ................................ 39
Vehicle Cleaning ................................ 40
Delivery to Customer .......................... 41
Printed in Canada. (rbl2014-003 en JL)
©2013 B ombardier Recreational Products Inc. and BRP US Inc. All rights reserved.
1/41
®™ and the BRP logo are trademarks of Bombardier Recreational Products Inc. or its affiliates.

Can-Am Spyder ST Limited SE5 Specifications

General

Brand	Can-Am
Model	Spyder ST Limited SE5
Category	Motorcycle
Language	English

Summary

UNCRATING

Front Wheels Installation

Step-by-step guide for installing the front wheels onto the vehicle.

PARTS TO BE INSTALLED

Front Cargo Module Installation

Detailed steps for installing the front cargo module onto the vehicle.

AAPTS Sensor Installation

Guide for connecting and installing the AAPTS sensor and routing its cable.

Low Beam Headlight Connection

Instructions for connecting the wiring harness to the low beam headlights.

Horn Connection

Steps to connect the horn connector and route its cable.

Latch Release Cable Installation

Procedure for feeding and attaching the latch release cable for the front storage cover.

Body Parts Installation

Front Fenders Installation

Windshield Installation

Rear Fender Installation

FLUIDS

Fueling Procedures

Clutch Fluid Check (SM5 Model)

Engine Coolant Level Verification

Brake Fluid Level Check

Engine Oil Level Verification

Procedures for checking engine oil level and recommended oil types.

SETUP

Tire Pressure Management

Drive Belt Tension Check

Headlight Aiming Adjustment

B.U.D.S. Programming Procedures

Steps for connecting the PC to the vehicle and programming using B.U.D.S. software.

ASSEMBLY INSPECTION

FINAL INSPECTION

Vehicle Test Run Procedure

Riding the vehicle to verify proper operation of all systems and components.

Customer Delivery Process