Cardinal 190 Series

To Next Page

To Previous Page

Model 190 Installation, Technical and Operation

8400-M022-O1 Rev J

Page 38

CAL3= – Last Calibration Weight

1. The display will show CAL3=. This weight is not used.

2. Press the UNITS/ key to skip CAL3= and advance to

SetgC? prompt.

Main Page

Default Chapter5
- Table of Contents5
1 Specifications11
- Standard Features12
- Optional Features12
- European Declaration of Conformity13
2 Precautions15
- Static Electricity15
- Batteries15
3 Installation17
- Site Preparation Requirements17
- Mounting20
- Load Cell Connections21
- Load Cell Connections with over 30 Feet of Cable23
- Sense and Deal Load Jumpers23
- Serial and I/O Cable Installation24
- P3 I/O Interconnections25
- P2 Power Connections25
- Re-Installing the Front Panel26
4 Indicator Setup27
- Calibration Inhibit Jumper27
- Calibration Data Entry29
- Accessing Setup31
- Settings33
- Analog to Digital Filtering41
  - Filter Setting Recommendations43
- Calibration45
- Set Gravity Constant61
- Serial Input/Output63
- Print Tab Settings67
- Fine Span Adjustment71
- Display High Resolution Weight73
- Key Lockout Feature75
- Options Setup79
- Function Setup81
- Display Backlight Color Setup85
5 Keypad87
- Standard Key Functions87
- Fn/ Key Functions91
- Fn/ Key Combination Features93
6 Annunicators95
- Battery Status98
7 Indicator Setup Review99
- Accessing Setup Review99
8 Operation101
- Ticket Format Selection101
- Preset Weight Comparators103
- Hold Function105
- Count Function107
- Time and Date Functions109
- Peak Hold Function111
- Checkweigher113
- Live Weight Function117
- Accumulated Weight Function119
- Touch Key Lock out Function121
- ASCII Commands123
9 Error Messages129
- Before You Call Service129
- Error Codes131
10 Event Counters133
- Accessing the Event Counters133
11 Test Mode/ Diagnostics135
- Test Mode/Diagnostics Features135
- Accessing Test Mode/Diagnostics135
12 Parts Identification136
- Front Sub-Assembly136
- Rear Sub-Assembly138
- Power Supply Sub-Assy139
- AC Wiring Detail140
- P2 Wiring Detail140
- 190DC Rear Sub-Assembly141
- 190DC Power Supply Sub-Assy142
- 190DC Wiring Detail143
- 190DC POWER OPTIONS (Not Shown)143
13 APPENDIX A - BP190 Optional Battery Pack145
- BP190 Contents145
- BP190 Specifications145
- Installing the BP190146
14 APPENDIX B - Model 190A149
- Traffic Control149
- Axle Weighing Mode150
- Standard Axle Weighing Operation153
- Auto Axle Weighing Operation155
- Wiring156
- Scoreboard Interconnections157
15 APPENDIX C - 190-RS232 Option159
- Specifications159
- Onboard Status/Diagnostic Led's159
- Setup160
- 190-RS232 Wiring162
- 190-RS232 Operation162
16 APPENDIX D - 190-IP Option163
- Features163
- Onboard Status/Diagnostic Led's163
- Setup164
- Ethernet Cable Installation165
- IP Address Setup165
- 190-IP Operation165
- XPORT Connector Status Led's166
17 APPENDIX E - 190-Wifi Option167
- Specifications167
- Onboard Status/Diagnostic Led's168
- Setup169
- Network Configuration171
- Wifi Operation177
18 APPENDIX F - 190-DAC Option179
- Specifications179
- Onboard Status/Diagnostic Led's180
- Setup181
- DAC Wiring183
19 APPENDIX G - 190-USB Option185
- Features185
- Onboard Status/Diagnostic Led's185
- Setup186
- 190-USB Operation188

Cardinal 190 Series - Page 48

Table of Contents

Related product manuals