21
ENG
“humiSonic ventilation” +0300063EN - rel. 1.3 - 14.05.2021
5. USER INTERFACE “MAIN” PANEL
5.1 Graphic terminal
The built-in terminal on the “Main” electrical panel comprises the display
and the keypad, featuring 6 buttons, which are used to perform all the
configuration and programming operations on humiSonic.
5.2 Keypad
On
29/05/2015 Fri 12:30
ON
OFF
Production 0.5Kg/h
Fig. 5.a
BUTTON DESCRIPTION
29/05/2015 Fri 12:30
Disabled
Carico
Disabilitato
Scarico
Autotest
Produzione
Carico
Autotest
Carico
Alarm
• Display the list of active alarms
• Reset alarms with manual reset
29/05/2015 Fri 12:30
Disabled
Carico
Disabilitato
Scarico
Autotest
Produzione
Carico
Autotest
Carico
Prg
Access to the main menu
29/05/2015 Fri 12:30
Disabled
Carico
Disabilitato
Scarico
Autotest
Produzione
Carico
Autotest
Carico
Esc
Return to the previous screen
29/05/2015 Fri 12:30
Disabled
Carico
Disabilitato
Scarico
Autotest
Produzione
Carico
Autotest
Carico
/
29/05/2015 Fri 12:30
Disabled
Carico
Disabilitato
Scarico
Autotest
Produzione
Carico
Autotest
Carico
Up / Down
• Scroll between screens
• Increase / decrease the value
29/05/2015 Fri 12:30
Disabled
Carico
Disabilitato
Scarico
Autotest
Produzione
Carico
Autotest
Carico
Enter
• Switch from display mode to setting mode
• Confirm the value and move to the next parameter
Tab. 5.a
5.3 Display
During normal operation, the display shows, as well as the current
date and time, the type of control selected, the reading of the control
probe and limit probe (if featured), and the quantity of atomised water
produced.
29/05/2015 Fri 12:30
On
ON
OFF
3
9
Unit Offline
2
Production 0.5Kg/h
5
99.2rH%
6
4
10
Fig. 5.b
Key
1 Current date/time 6 Limit humidity probe reading
2
Cause of unit shutdown/Unit
status
7 Unit status icon/active actuators
3 Request 8 Quick access button menu icon
4 Control type selected 9 Maintenance required
5 Unit status 10 Time bands enabled
CAUSE OF UNIT SHUTDOWN
Message Description
Off by Key Off from keypad
Unit Offline Unit offline
Remote On/Off Remote On/Off
No request No request
Unit disabled Unit disabled
Alarms Alarms
Manual mode Manual mode
Off from BMS Off from BMS
Off from Sched. Off from Sched.
Tab. 5.a
UNIT STATUS
Message Description
Production …Kg/h/(lb/h) Instant production in kg/h (lb/h)
Drain Drain
Init Initialisation
Fill Filling
Autotest Autotest
Waiting (.. min) Waiting (.. min) to restart
Disabled Disabled
Tab. 5.b
Request Meaning Control type
On/-- On= request
--- = no request
On/Off
0 to 100 % Request percentage
%
Ext. regulator
rH%: Control probe reading in rH% rH% probe
°C Control probe reading in °C T probe
Tab. 5.c
Unit status/ active actuators Meaning
Production in progress
Fill in progress
Drain open
Water present
Stop transducer control
Malfunction
Tab. 5.d
Note: the control type is selectable in user menu F, under screen Fa01:
Regulation. See the parameter table.
To Next Page
Loading...
