Carel humiSteam UE005 - 1 Introduction and Assembly; Humisteam (UEY*); Dimensions and Weights; Opening the Packaging

7
“UE BASIC” +08C0042EZ - rel. 1.0 - 16.10.2017
ENG
1. INTRODUCTION AND ASSEMBLY
1.1 humiSteam (UEY*)
Range of isothermal immersed electrode humidiers with backlit display
for the control and distribution of steam.
Models available (identiable from the code shown on the product):
• UE005, UE008, UE010, UE015, with steam production capacity up to 15
kg/h, water connections under the base of the humidier;
• UE025, UE035, UE045, UE065 with steam production capacity from 25
to 65 kg/h, water connections on the side of the humidier.
1.2 Dimensions and weights
Models UE005 to UE015 Models UE025 to UE065
B
B
A
C
A
C
Fig. 1.a
UE005 to
UE008
UE010 to
UE015
UE025 to
UE045
UE065
dimensions
mm (“)
A 365 (14.4) 545 (21.5) 635 (25.0)
B 275 (10.8) 375 (14.8) 465 (18.3)
C 712 (28.0) 815 (32.0) 890 (35.0)
weights
kg (lb)
packaged 16 (35.3) 20 (44.0) 39 (86.0) 51 (112.4)
empty 13,5 (29.8) 17 (37.5) 34 (74.9) 44 (97.0)
installed* 19 (41.9) 27 (59.5) 60,5 (133.4) 94 (207.2)
Tab. 1.aTab. 1.a
*: in operating conditions
1.3 Opening the packaging
Ƒ make sure the humidier is intact upon delivery and immediately
notify the transporter, in writing, of any damage that may be due to
careless or improper transport;
Ƒ move the humidier to the site of installation before removing from
the packaging, grasping the neck only from underneath the base;
Ƒ open the cardboard box, remove the protective material and remove
the humidier, keeping it vertical at all times.
1.4 Positioning
• the unit is designed to be mounted on a wall that is strong enough
to support the weight in normal operating conditions (see Wall-
mounting below). Models UE025 to UE065 can stand on the oor;
• to ensure correct steam distribution, position the humidier near the
point of steam distribution;
• make sure the humidier is level, allowing the minimum clearances
(see Fig. 1.b) for maintenance operations.
Important: during operation the metal casing heats up and the
rear part resting against the wall may reach temperatures in
excess of 60 °C (140 °F) .
Distances from walls
Models UE005 to UE015 Models UE025 to UE065
≥ 500
(16.4”)
<0,5°
≥ 200
(7.9”)
≥ 200
(7.9”)
≥ 200
(7.9”)
≥ 400
(15.7”)
≥ 200
(7.9”)
≥ 200
(7.9”)
≥ 700
(27.6”)
≥ 700
(27.6”)
Fig. 1.b
1.5 Wall-mounting
Fit the humidier on the wall using the support bracket and the screw kit
supplied (for the dimensions in mm see Fig. 1.d).
Assembly instructions:
1. unscrew the wall bracket from the humidier bracket;
2. fasten the wall bracket (see Fig. 1.e), checking horizontal position
with a spirit level; if installed on a masonry wall, the plastic anchor
plugs (dia. 8 mm/0.31” ) and screws (dia. 5 mm x L= 50 mm/ 0.19” x L=
1.97” ) supplied can be used;
3. hang the appliance to the bracket using the slot on the top edge of
the rear of the appliance;
4. secure the appliance to the wall through the hole in the centre on
the rear of the unit. For the weights and dimensions see Figs. 1.a,
1.b, 1.c.
Models UE005 to UE065
bracket
X
Fig. 1.c