Name: Carrier Access Wide Bank 28 DS3
Brand: Carrier Access
Rating: 4 (1 reviews)

To Next Page

Wide Bank 28 DS3

USER MANUAL

Fan Faceplate Option (FFO)

Document: 770-0074-AT

Product Release: 2.4

July 2004

Compliance4
FCC Requirements, Part 154
FCC Requirements, Part 68 Exhibit J14
Safety Requirements for Telecommunications Equipment5
Industry Canada Requirements5
Japan Approvals Institute for Telecommunication Equipment (JATE)6
Network Equipment Building System (NEBS) Requirements6
Notices6
Electrostatic Discharge Guidelines7
Warranty8
Limitations of Warranty and Remedies8
Warranty Product Returns9
Table of Contents11
Introduction28
System Overview28
Features, Functions, and Options29
Wide Bank 28 DS3 Features29
DS3 Ports30
DS1 and E1 Ports30
Independent Clocking and Transparent Framing30
Manageability31
Security31
Basic Security31
Security Upgrade Option32
Management Capabilities33
Command Line Interface34
Snmp34
Networkvalet Software35
Transaction Language 1 (TL1)35
Product Description38
Overview38
Features38
Redundant Architecture40
Physical Characteristics41
Connector Panel Interfaces42
Framing Modes44
Additional Functions Available in C-Bit Mode44
DS3 Multiframe Structure45
X-Bits - Error Message from Far-End to Near-End46
Application Identification Channel (AIC) Bit46
Reserved Network Application (Na) Bit46
Far End Alarm (FEA) Bit47
CP Bits47
P-Bits47
Far-End Block Error (FEBE) Bits47
Dlt Bits49
LED Test and Status Indicators50
Critical and Major/Minor Alarm Definitions51
Line Code Violations and Bipolar Violations51
Controller and DS3 Redundancy53
Protection Modes53
Electronics Protection Mode53
Setting the Arm and Revertive Software Switches54
Electronics and Network Protection Mode55
Operator-Initiated Switch56
Restoring to Original Status (Revertive Switching)56
Revertive Switching with Electronics Protection56
Revertive Switching with Electronics and Network Protection56
Low-Speed (LS) Redundancy58
Low-Speed Automatic Switchover58
Low-Speed Circuit Groups58
Switchover Lockouts Within Groups58
Maintenance Service Option (MSO)60
Failures that Cause a Low-Speed Switchover62
Enabling and Disabling Low-Speed Switchovers62
Restoring to Original Status (Revertive Switching)63
Hot-Swapping a Failed Standard Low-Speed Card63
Hot-Swapping a Failed MSO Low-Speed Card63
MSO Conflicts with Spare Card64
Tests and Loopbacks65
Transmission Path Verification65
Low-Speed Loopback Modes66
Low-Speed Line Loopback66
Low-Speed Equipment Loopback66
Low-Speed Metallic Loopback67
C-Bit FEAC Loopback Code Word Detection67
NIU Loopcode Detection67
Low-Speed Performance Monitoring68
LS Alarm Signals68
DS3 Loopback Modes68
DS3 Line Loopback68
DS3 Payload Loopback69
DS3 Equipment Loopback69
DS3 Loopcode Detection70
Internal Tests70
DS3 Alarm and Performance Monitoring70
DS3 Alarm Signals70
DS3 Errors70
Technical Specifications72
Specifications72
System Parameters72
DS3 (44.736 Mbps) Interface73
DS1 (1.544 Mbps) Interface74
E1 (2.048 Mbps) Interface74
Specifications74
Cable Compensation75
Management75
Alarms75
DS3 Transmit Clock Source75
Power76
Environmental76
Physical Dimensions76
Standards Compliance77
Safety77
Industry77
Installation78
Physical Installation80
Installation Preparation and Requirements80
Mounting the Wide Bank 28 DS381
Attaching Mounting Brackets to the Units82
Rack Mounting - Non-FFO Equipped Units84
Horizontal Mounting in a Standard EIA or WECO Rack84
Vertical Mounting in a Standard EIA or WECO Rack85
Rack Mounting - FFO-Equipped Units87
Fan Faceplate Option87
Rack Mounting (High-Density)88
Mounting the Power Converter/Battery Charger89
Mounting the Battery Unit89
Wall-Mounting the Battery Unit89
Rack Mounting the Power Converter & Battery Unit92
Electrical Installation and Cabling94
Cabling and Compliance Requirements94
Maintaining NEBS 1089 and FCC Part 15 Compliance94
Static-Sensitive Equipment Handling Procedures95
Connector Panel Interface and Power Connectors96
Cable and Wiring Layout97
Ground Connection98
Low-Speed DS1/E1 Cables99
High-Speed DS3 Cables101
External Clock Cable101
Management Cables102
CLI RS-232 Management Cable102
TL1 RS-232 Port Cable103
Ethernet Management Port103
External Alarm Wiring104
Power Wiring105
DC Power Connector Input Requirements105
Wiring the Power Plugs106
Connecting to Power Source107
Applying Power108
Configuration110
Configuration Overview110
Basic Configuration111
Connecting to the Management Port111
Logging on112
Working Configurations112
Saving a Temporary Copy of Configuration113
Restoring a Temporarily Saved Configuration113
Saving the Configuration to a User File System113
Restoring Saved Configuration from User File System113
Restoring Factory Defaults114
Validating Equipment114
Setting the Time and Date115
Set System Time115
Set System Date115
Setting System Security, Users, and Login Passwords (Basic Security)115
Access Levels (Basic Security)116
Password Protection (Basic Security)116
Display Current Security Status (Basic Security)117
Change the Security Status (Basic Security)117
Add a User (Basic Security)117
Assign or Change a User's Password (Basic Security)117
Set a User's Access Level (Basic Security)117
Delete a User (Basic Security)117
Show Current User Settings (Basic Security)117
Setting System Security, Users, and Login Passwords (Security Upgrade Option)118
Access Levels (Security Upgrade Option)119
Password Protection (Security Upgrade Option)119
User Interface Access (Security Upgrade Option)120
Display Current Security Status (Security Upgrade Option)121
Change the Security Status (Security Upgrade Option)121
Add a User and Assign a Password (Security Upgrade Option)121
Change a User's Password (Security Upgrade Option)121
Set a User's Access Level (Security Upgrade Option)121
Delete a User (Security Upgrade Option)121
Show Current User Settings (Security Upgrade Option)122
Set CLI Time-Out (Security Upgrade Option)122
Disable Ethernet Port (Security Upgrade Option)122
Disable 9-Pin RS-232 CLI Port (Security Upgrade Option)122
Disable 25-Pin RS-232 TL1 Port (Security Upgrade Option)122
Disable SNMP Management (Security Upgrade Option)123
Disable TL1 Management (Security Upgrade Option)123
Configuring IP and PPP Addresses123
Verify Network Settings124
IP Routing with Point-To-Point Protocol (PPP)125
IP over PPP Applications125
Configuring DS3125
Configuring Low-Speed Ports127
Saving the Configuration127
Verify All System Parameters128
Verifying Autocopy to Secondary Controller130
Turning off Unused or Unterminated Low-Speed Channels130
Logging off130
Downloading New Software131
Configurations for Downloading Firmware131
Management Connections for Downloading Firmware131
Protocol Options for Downloading Firmware132
Downloading to a Redundant Wide Bank 28 DS3134
Downloading to a Non-Redundant Wide Bank 28 DS3140
Xmodem Download Initiated Via RS-232140
TFTP Download Initiated Via RS-232 or Ethernet143
Diagnostics & Troubleshooting146
LED Test and Status Indicators146
Power LED147
Alarm Cutoff (ACO) LED and Pushbutton147
Critical (CR) Alarms148
Major/Minor (MJ/MN) Alarms148
Controller Status (CS) LED149
High Speed (HS) Line Condition LED149
Low-Speed DS1/E1 Line Status Leds (One Per Span)150
Ethernet Status LED150
Determining Performance and Status151
DS3 Far-End Statistics151
DS3 Path Maintenance Data Link151
Functional Description of DS3 Path Maintenance Data Link151
Point-To-Point Protocol Status152
General Troubleshooting153
Thermal Shut-Down154
Self-Tests155
The DS1/E1 Test156
Low-Speed Card Self-Test156
DS3 Card Self-Test156
The DS3 Test156
FFO Test and Monitoring157
Complete Self-Test (Power-Up Test)158
The Complete Self-Test158
Looptests Using Built-In PRBS BERT159
Low-Speed CSU Loopup Drop with PRBS BERT159
Low-Speed NIU Loopup Network with PRBS BERT160
DS3 Loopup Network with PRBS BERT161
Testing Low-Speed Interface Operation162
Testing Low-Speed Near-End with Loop Tests163
DS1 Line Loopback164
DS1 Equipment Loopback164
DS1 Metallic Loopback165
DS1 NIU Loopback166
DS1 NIU Loopback Using Two Wide Banks167
DS1 Send CSU Loopback Toward Drop168
DS1 Send NIU Loopup Code Toward Drop169
DS1 Send NIU Loopup Code Toward Network170
Testing the Low-Speed Far-End with Loop Tests171
Activating Far-End Loopbacks in M23 Framing Mode171
Activating Far-End Loopbacks in C-Bit Framing Mode171
Testing the Network to the Far-End through a Low-Speed Drop172
Running Maintenance Tests on a Low-Speed Circuit173
Testing DS3 Interfaces176
Testing DS3 Framing and Loop Timing176
DS3 Non-Redundant Test Setup176
DS3 Test with M23 Framing177
DS3 Test with C-Bit Framing177
DS3 Tests with Line Timing178
Testing the DS3 Near-End with Loopback Tests179
DS3 Equipment Loopback179
DS3 Line Loopback with M23 Framing179
DS3 Line Loopback with C-Bit Framing180
DS3 Payload Loopback with M23 Framing180
DS3 Payload Loopback with C-Bit Framing180
Testing the DS3 Far-End with Loopback Tests181
Far-End Loop Codes181
Testing DS3 Redundancy183
Testing Electronics Protection183
DS3 Test Setup183
DS3 Manual Switch Test184
DS3 Automatic Protection Test184
DS3 Revertive Switching Test185
Testing Electronics and Network Protection186
DS3 Test Setup186
DS3 Network Protection Test186
DS3 Electronics Protection Test187
CLI Commands and Messages190
Management Overview190
Management Interfaces190
Redundant DS3 Network Interfaces191
Telnet Interface191
Security Levels192
Basic Security192
Security Upgrade Option192
Security Integrity193
SNMP Traps193
Command Line Interface194
Using the Command Line Interface194
Context Sensitive Help195
CLI Command List197
CLI Command Syntax198
CLI Shortcuts (Recall and Edit)198
Aco199
Alarms199
Alarms Standby199
Alarmout201
Arm201
Autocopy202
Clear202
Config203
Controller205
Copy206
Date206
Day207
Ds1209
Ds1 Ains210
Ds1 Circuitid211
Ds1 Enable/Disable211
Ds1 Equipment212
Ds1 Length213
Ds1 Line213
Ds1 Linecode214
Ds1 Loopdetect215
Ds1 Metallic215
Ds1 Move216
Ds1 Pm Threshold217
Ds1 Protect218
Ds1 Send218
Ds3220
Ds3 Circuitid221
Ds3 Clock221
Ds3 Clockrevert222
Ds3 Equipment222
Ds3 Equipmentid223
Ds3 Facilityid223
Ds3 Frameid223
Ds3 Framing224
Ds3 Gennumber224
Ds3 Length225
Ds3 Line225
Ds3 Locationid225
Ds3 Loopdetect226
Ds3 Payload226
Ds3 Pm Threshold227
Ds3 Portnumber229
Ds3 Protect229
Ds3 Send230
Ds3 Threshold230
Ds3 Unit231
Equipment231
Exit233
Ffo Present233
Help234
Hour235
Load237
Log238
Ls Ains239
Ls Circuitid241
Ls Enable/Disable241
Ls Length243
Ls Line244
Ls Linecode244
Ls Loopdetect245
Ls Metallic245
Lsmode246
Ls Move247
Ls Pm Threshold247
Ls Protect249
Ls Send249
Ping251
Program Flash251
Restore251
Results254
Revertive255
Save256
Screen257
Security257
Security Cli258
Security Ethernet259
Security Rs232Cli259
Security Rs232Tl1260
Security Snmp261
Security Tl1261
Snmp262
Status263
Switch266
Temp Copy267
Test267
Time268
Tl1269
User270
Version273
TL1 Commands and Messages277
TL1 Overview277
General Syntax277
Command Syntax277
Grouping Values as Lists and Ranges277
Response Syntax277
Multiple Output Responses279
Error Responses280
Command Categories281
Security Commands281
Transport Surveillance Commands281
Memory Administration Commands281
Network Maintenance Commands281
Command Modifiers281
Facilitytype281
Lstype281
Aidtype282
Security Levels282
TL1 Shortcuts (Recall and Edit)282
TL1 Setup and Configuration283
Connecting and Configuring for TL1283
Establishing a TL1 Session Via a TCP/IP Socket283
Establishing a TL1 Session Via the RS-232 TL1 Port284
Establishing a TL1 Session Using Terminal-To-Terminal Link284
Setting the Network/Prompt/Source/Target Identifier284
Using CLI to Set the Network Identifier284
Using TL1 to Set the Identifier284
Setting the Initial TL1 Admin Password285
Activating a TL1 User Session285
TL1 Commands and Response Messages285
Activating Users286
Normal Response to Activate User Command286
Error Response for Incorrect Password287
Adding Users287
Deleting Users287
Normal Response to Delete User Command288
Changing User Properties288
Changing User Password288
Retrieving Users288
Retrieving Alarms289
Response if no Alarms Are Present289
Response if Alarms Are Present289
Retrieve Header Command289
Testing TL1 Alarming290
Canceling the TL1 User Session290
Error Message in Response to Commands Not Recognized or Supported290
Error Response to Valid Commands Received When a User Is Not Logged in290
TL1 Command List292
Act-User292
Alw-Autorst292
Alw-Log-Secu293
ALW-LPBK-<Facilitytype294
ALW-MSG-<Aidtype294
ALW-PMREPT-<Facilitytype296
ALW-SWTOPROTN-<Facilitytype296
ALW-SWTOWKG-<Facilitytype297
Canc-User297
Canc-User-Secu298
CONN-LPBK-<Lstype298
Conn-Lpbk-T3299
Cpy-Mem299
DGN-<Aidtype300
DISC-LPBK-<Facilitytype301
DLT-<Lstype302
Dlt-User-Secu302
ED-<Aidtype303
Ed-Dat305
Ed-Pid305
Ed-User-Secu306
ENT-<Lstype307
Ent-User-Secu308
Inh-Autorst309
Inh-Log-Secu309
INH-LPBK-<Facilitytype310
INH-MSG-<Aidtype311
INH-PMREPT-<Facilitytype312
INH-SWTOPROTN-<Facilitytype312
Inh-Swtowkg313
Init-Log313
INIT-REG-<Facilitytype314
Init-Sys315
Opr-Aco-All315
OPR-ARC-<Lstype315
OPR-LPBK-<Facilitytype317
Rd-Mem-File317
RLS-ARC-<Lstype318
RLS-LPBK-<Facilitytype319
RMV-<Aidtype320
RST-<Aidtype320
RTRV-<Facilitytype321
RTRV-ALM-<Aidtype325
Rtrv-Alm-Env327
Rtrv-Ao328
RTRV-ARC-<Lstype329
RTRV-ATTR-<Aidtype330
RTRV-COND-<Aidtype333
Rtrv-Eqpt335
Rtrv-Hdr336
Rtrv-Log336
Rtrv-Netype337
RTRV-PM-<Facilitytype338
RTRV-PMSCHED-<Facilitytype341
Rtrv-Status344
RTRV-TH-<Facilitytype345
Rtrv-Tod346
Rtrv-User-Secu346
SCHED-PMREPT-<Facilitytype348
SET-ATTR-<Aidtype349
Set-Attr-Secudflt351
Set-Sid352
SET-TH-<Facilitytype353
Sta-Locl-Rst354
SW-TOPROTN-<Facilitytype354
SW-TOWKG-<Facilitytype355
Wrt-Mem-File356
Access Identifier <Aid358
Error Response: Invalid Access Identifier359
Access Identifier Types <Aidtype359
Error Response: Invalid Access Identifier Type359
Additional Access Identifier Information <Aiddet360
Alarm Code <Almcde360
Alarm Message <Almmsg360
ATAG Segment <Atagseg360
Automatic Message Tag <Atag360
Command Mode <Cmdmde360
Completion Codes361
Condition Description <Conddescr361
Condition Effect <Condeff361
Condition Type <Condtype361
Alarmed Condition Types361
Error Response: Invalid Condition Type362
Correlation Tag <Ctag363
Data Segment <Data_Seg363
Date <Date363
Direction of Alarm or Condition <Dirn363
Error Response: Invalid Direction364
DS1/E1 Properties364
Error Message: Invalid T1/E1 Parameter or Value364
DS3 Properties365
Error Message: Invalid T3 Parameter or Value365
Environment Access Identifier (Envaid)365
Equipment Parameters366
Error Message: Invalid Equipment Parameter Value366
Error Message: Invalid Test Session Number366
Location of Alarm or Condition <Locn366
Error Response: Invalid Location366
Log Identifier <Lognm367
Error Response: Invalid Log Identifier367
Loopback Type <Lpbktype367
Error Response: Invalid Loopback Type367
Memory <Frommem> and <Tomem368
Message Type <Msgtype368
Monitor Date <Mondat368
Monitor Level <Monlev368
Monitor Time <Montm368
Monitored Parameter Type <Montype369
Error Response: Invalid Monitored Parameter Type369
Notification Code <Ntfncde370
Error Response: Invalid Notification Code370
Number of Reports <Numrept370
Occurrence Date <Ocrdat370
Occurrence Time <Ocrtm370
Phase <Ph370
Private Identifier <Pid371
Reporting Interval <Reptinvl371
Reporting Start Time <Reptstatm371
Restoration Function Codes371
Security Alarm Type <Secualmtype371
Service Effect of Alarm or Condition <Srveff372
Error Response: Invalid Service372
Target Identifier <Tid> and Source Identifier <Sid372
Threshold Level <Thlev372
Time <Time373
Time Offset <Tmofst373
Time Period <Tmper373
Error Response: Invalid Time Period373
Type or Request <Typereq373
User Access Privilege <Uap373
Error Response: Illegal User Access Privilege374
Error Response: Insufficient Privilege to Execute Command374
User Identifier <Uid374
TL1 Automatic Messages375
Report Alarm Message Format375
Report Alarm Clear Message Format377
Report Event Message Format378
Report Performance Monitoring Message Format379
Cancel User Session Event Message Format380
DS3 Far-End Alarms380
Message Summary Table380
Card Maintenance388
Card Locations388
Removing and Installing Faceplates389
Standard Faceplates389
Fan Faceplates389
Replacing Low-Speed Cards391
Maintenance Practices for Low-Speed Cards391
Standard Low-Speed Card Maintenance Practice391
MSO Low-Speed Maintenance Practice391
Replacing a Standard Low-Speed Card392
Replacing an MSO Low-Speed Card393
Removing the Electronics Section of an MSO Card394
Inserting the Electronics Section of an MSO Card395
Replacing DS3 Controller Cards396
Turning off Unused or Unterminated Low-Speed Channels397
Configuration for SNMP400
Basic Configuration Parameters400
Wide Bank IP Address400
Subnet Mask400
Network Management Station (NMS) IP Address400
System Name400
Location401
Contact401
Basic Configuration from the CLI401
Validate Link402
Carrier Access DS3 Multiplexer Enterprise Mibs403
Authentication Failure Trap404
Warm Start Trap405
Link down Trap405
Link up Trap405
Enterprise Traps406
DS3 Controller State Trap406
DS1 Card State Trap406
Failed CLI Login Trap406
Power Status Trap406
DS1 Protect Switch Trap406
DS1 Move Home Trap406
DS1 Internal Harware Failure Trap407
DS1 Internal Hardware Failure Clear Trap407
DS1 Internal Hardware Failure Spare Trap407
DS1 Internal Hardware Failure Spare Clear Trap407
Alarm Reporting410
Overview410
Critical, Major and Minor Alarms410
Leds that Report Alarms411
DS3 Far-End Alarms and Control (FEAC)412
Far-End Alarm Transmission412
Far-End Alarm Reporting412
TL1 Alarm Reporting412
TL1 Automatic Messages412
Connector Pinouts414
DC Power Connectors414
Alarm Contacts415
Low-Speed DS1/E1 (DSX-1) Connector Pinouts416
Low-Speed Connector Pinout Chart416
CLI RS-232 Management Port Pinout419
Male DB9 Connector419
Female DB9 Connector419
TL1 RS-232 Management Port Pinout420
Male DB25 Connector420
Female DB25 Connector420
Ethernet RJ-45 (10Base-T) Pinout421
RJ-45 Connector421

Carrier Access Wide Bank 28 DS3 User Manual

Table of Contents

Other manuals for Carrier Access Wide Bank 28 DS3

Questions and Answers:

Carrier Access Wide Bank 28 DS3 Specifications

Category	Multiplexer
Product Name	Carrier Access Wide Bank 28 DS3
DS3 Ports	28
Manufacturer	Carrier Access
Interface	DS3