Carrier 50FC - Service Clearance for Larger Units

21
9 - DISPLAY OF THE INPUTS / OUTPUTS STATUS
All variables which are controlled by the system are displayed in
this group of screens, including the status of the digital inputs, the
digital outputs and the analogue outputs, both the main board and
the installed expansion cards.
This group of screens is accessed from the MAIN MENU, in E.
INPUTS/OUTPUTS.
 Values measured by the sensors: screen I01, I01a, I01b, I02, I03,
I03a, I03b, I03c, I04a, I04b, I05a, I05c, I05e, I06a, I06b, I12d.
I01
S1 probe
Return temperature
probe 16.0ßC
S2 probe
Outdoor temperature
probe 20.0ßC
 Cumulated operating hours by the unit and each compressor:
screens I07, I07a.
I07
Operating hours
Unit: 00000
Compress. 1-C1:00000
Compress. 2-C1:00000
 Digital inputs status: screen I08 (main board), screen I08b
(expansion card addr.8), screen I08c (expansion card addr.9).
I08
Digital input
status (1...10):
C C C C C C C C C C
C: Closed contact
O: Open contact
I09
Compressor 1 - C1 OFF
Compressor 2 - C1 OFF
Compressor 1 - C2 OFF
Compressor 2 - C2 OFF
 Digital outputs status: screens I09, I09a, I10, I11 (main board),
I10b (expansion card addr.8), I10c (expansion card addr.9).
 Analogue outputs status: screens I12, I12a (main board), screen
I12b (expansion card addr.8), screen I12c (expansion card addr.9).
I12
Outdoor damper: 025%
Heat valve: 000%
000%: opening percentage
 Cooling recovery circuit reading (optional): screens I06cr1, I06cr2,
I06fr, I06er, I05ar, I08cr, I10cr.
 Electronic expansion valve(s) reading: screens I06a1, I06b1,
I06c1, I06e, I06f, I06g.
 Calculation of the cooling and heating capacities (optional):
screens I18b, I18c, I18d, I18e.
Refriger. power: I18b
Input enthalpy
value: 00.0 kcal/kg
Input humidity
value: 50.0 %
Input temperature
value: 000.0C
10 - VERSIONS OF SOFTWARE AND HARDWARE
SOFTWARE V01
"50FC" Contro1
Version: 16.2.0
Date: 09/05/23
SO: 5.1.6
Boot: 5.1.6
HARDWARE V02
Board type: uPC3
Board size: Medium
Main cycle: 247ms
4.0 cycles/s
In this group of screens O. CRTL_ID from the MAIN MENU, the
Software version installed on the control board is provided.
The second screen of this menu shows the main features of the
hardware.
Energy meter I15
Voltages
V L1-L2: 000.0 V
V L2-L3: 000.0 V
V L3-L1: 000.0 V
V L1: 000.0 V
V L2: 000.0 V
V L3: 000.0 V
 Optional element readings: energy meter: screens I15, I16, I17,
I18; and R-410A leak detector: screen I18a.
Active recovey I06cr1
Cooling capacity: 000%
Pres.HP: 000.0bar
HP. Temp: 000.0ßC
suct. T: 000.0ßC
evap P: 000.0barg
evap T: 000.0ßC
EEV I06a
Opening: 0000stp
000.0%
Status: ---
Protection: None
SH: 000.0K