39
13 - LIST OF CONTROL PARAMETERS WITH "ACCESS LEVEL 1"
Parameters of “Input/Output” (...continuation)
Screen Parameter Description of the parameter Value Min. Max. UOM Type R/W
Add.
BMS
I17 REACTIVE_POWER_TOTAL Reading of the energy meter: total reactive power 0.0 -999.9 999.9 kVAR Analog. R 315
I17 REACTIVE_ENERGY Reading of the energy meter: equivalent reactive energy 0 0 4294967295 kWhR Integer R 174,175
I18 POWER_L1 Reading of the energy meter: phase power L1 0.0 -999.9 999.9 W Analog. R 137
I18 POWER_L2 Reading of the energy meter: phase power L2 0.0 -999.9 999.9 W Analog. R 138
I18 POWER_L3 Reading of the energy meter: phase power L3 0.0 -999.9 999.9 W Analog. R 139
I18 POWER_TOTAL Reading of the energy meter: total power -999.9 999.9 kW Analog. R 140
I18 ENERGY Reading of the energy meter: energy 0 0 4294967295 kWh Integer R 176,177
I18 HOURMETER_EM Reading of the energy meter: time (hours) 0 0 4294967295 h Integer R 180,181
I18a DevAddr_GLD Number of the R-410A gas leak detector 6 0 999 --- Integer R/W
I18a
Concentration_Percent_Gas_
Leakag
Reading of the R-410A gas leak detector: concentration (%) 0 0 100 % Integer R 7
I18a
Concentration_ppm_Gas_
Leakag
Reading of the R-410A gas leak detector: concentration (ppm) 0 0 5000 ppm Integer R 6
I18a RedLedStatus_GLD Reading of the R-410A gas leak detector: red led (1: Active; 0: O ) 0 0 1 --- Digital R
I18a GreenLedStatus_GLD
Reading of the R-410A gas leak detector: green led (1: Active;
0: O )
0 0 1 --- Digital R
I18a Relay_Status_GLD Reading of the R-410A gas leak detector: relay (1: Active; 0: O ) 0 0 1 --- Digital R
I18b ENTALPIA_MEZCLA_KCAL
Calculation of cooling and heating capacities: display of input
enthalpy
0.0 -999.9 999.9 Kcal/Kg Analog. R 237
I18b SONDA_MEZCLA_HUM
Calculation of cooling and heating capacities: supply probe - display
of input humidity
0.0 0.0 100.0 %rH Analog. R/W 232
I18b SONDA_MEZCLA_TEMP
Calculation of cooling and heating capacities: mixing probe RS485
- display of input temperature
0.0 -999.9 999.9 °C Analog. R 231
I18c
ENTALPIA_IMPULSION_
KCAL
Calculation of cooling and heating capacities: display of output
enthalpy
0.0 -999.9 999.9 Kcal/Kg Analog. R 238
I18c SONDA_IMPULSION_HUM
Calculation of cooling and heating capacities: supply probe - display
of output humidity
0.0 0.0 100.0 %rH Analog. R 235
I18c SONDA_IMPULSION_TEMP
Calculation of cooling and heating capacities: mixing probe RS485
- display of output temperature
0.0 -999.9 999.9 °C Analog. R 234
I18d CAUDAL_IMPULSION_MSK Calculation of cooling and heating capacities: display of supply fl ow 0 -99999 99999
x10
m3/h
Integer R/W
I18d
DIF_ENTALPIA_POT_
TERMICA_KCAL
Calculation of cooling and heating capacities: display of the input-
output enthalpy di erence
0.0 -999.9 999.9 KJ/Kg Analog. R 268
I18d Densidad_aire_impulsion Calculation of cooling and heating capacities: display of air density 0 -99999 99999
x10
g/m3
Integer R 231
I18d Pot_termica
Calculation of cooling and heating capacities: display of total
capacity
0.0 -9999.9 9999.9 KW Analog. R 239
I18d POWER_TOTAL
Calculation of cooling and heating capacities: display of electric
power
0.0 -9999.9 9999.9 kW Analog. R 140
I18e MODO_FRIO_2 Calculation of cooling and heating capacities: operating mode 0 0 1 --- Digital R
I18e EER_COP
Calculation of cooling and heating capacities: display of EER /
COP calculation
0.0 -999.9 999.9 --- Analog. R 240
I18e ON_COMPRESOR
Calculation of cooling and heating capacities: display of started
compressors
0 0 1 --- Digital R 186
I18e PORC_COMPRESORES
Calculation of cooling and heating capacities: display of compressor
stages (%)
0 0 100 % Integer R 232
I18e COMPRESOR_REC
Calculation of cooling and heating capacities: display of recovery
compressor
0 0 1 --- Digital R/W 117
I18e RENOVACION_CAL
Calculation of cooling and heating capacities: display of air renewal
calculated depending on the mixing probe or the CO2 probe
0 0 100 % Integer R 124
I18e TEMP_INT
Calculation of cooling and heating capacities: display of indoor
temperature used in the unit control
0.0 -99.9 99.9 °C Analog. R/W 291
I18e TEMP_EXT
Calculation of cooling and heating capacities: display of outdoor
temperature
0.0 -99.9 99.9 °C Analog. R/W 2
I06cr1 T_P_HP_CR Display of the high pressure transducer of the recovery circuit 0.0 -999.9 999.9 bar Analog. R 263
I06cr1 TEMP_CAL_HP_CR Calculated temperature for high pressure of the recovery circuit 0.0 -999.9 999.9 °C Analog. R 265
I06cr1 COMPRESOR_REC Contactor of recovery circuit compressor 0 0 1 --- Digital R 117
I06cr1 TEMP_ASP_CR Suction temperature on the recovery circuit 0.0 -999.9 999.9 °C Analog. R 259
I06cr1 T_P_LP_CR Evaporating pressure on the recovery circuit 0.0 -999.9 999.9 bar Analog. R 264
I06cr1 TEMP_CAL_LP_CR Evaporating temperature on the recovery circuit 0.0 -999.9 999.9 °C Analog. R 266
I06cr2 EEV_POS_STEPS_CR Valve position (steps) of the recovery circuit 0 -9999 9999 --- Integer R
I06cr2 EEV_POS_PERCENT_CR Valve opening (%) of the recovery circuit 0.0 0.0 100.0 % Analog. R 261
I06cr2 EVD_CR_RegStatus Status of the recovery circuit valve 0 -32768 32767 --- Integer R
I06cr2 EVD_CR_ProtStatus Status of the recovery circuit valve protection 0 -32768 32767 --- Integer R
I06cr2 SH_EVOS_CR Overheating on the expansion valve of the recovery circuit 0.0 -999.9 999.9 ºC Analog. R 260
INPUTS/OUTPUTS
E
To Next Page
Loading...
