Carrier SUPRA 950Mt - Page 49

3-23-2
3. 3.
The micropThe microp
rocessrocess
or will energior will energi
ze glow cycle (lenze glow cycle (len
gthgth
of time depends on engine temperature) and startof time depends on engine temperature) and start
the engine.the engine.
4. T4. T
oo
chch
anan
gege
thethe
sese
tpotpo
inin
tt
prpr
eses
ss
thethe
UpUp
Or DoOr Do
wnwn
ArrArr
owow
KeyKey
and then theand then the
Enter KeyEnter Key
..
5. 5.
PrePre
ssss
inin
gg
thethe
AutoAuto
S/S-S/S-
-Continuou-Continuou
ss
KeyKey
changchang
eses
thethe
operation of the unit between automatic start/stopoperation of the unit between automatic start/stop
(unit will automatically start and stop in response to(unit will automatically start and stop in response to
chch
anan
gigi
ng ng
bobo
x x
temtem
pepe
ratrat
urur
e) e)
or or
auau
tomtom
atiati
c c
stasta
rtrt
continuous run (unit will operate continuously aftercontinuous run (unit will operate continuously after
star-ting).star-ting).
c. c.
Stopping Stopping
instrucinstruc
tionstions
Place thePlace the
On-Off SwitchOn-Off Switch
(Cab Command) to OFF(Cab Command) to OFF
pospos
itioitio
nn
oror
plapla
cece
Run-StoRun-Sto
pp
SwitchSwitch
inin
the the
STOPSTOP
pospos
itioitio
nn
to stop unit.to stop unit.
3.3 3.3
STST
ARTINARTIN
G G
AND AND
STOPPSTOPP
ING ING
INSTRINSTR
UCTIONUCTION
SS
--
- -
STANDBY MOTOR STANDBY MOTOR
DRIVEDRIVE
WARNINGWARNING
CheChe
ck ck
for corrfor corr
ect power connect power conn
ectect
ionion
(2(2
2020
V V
or or
33
8080
VV
) )
wiwi
th th
coco
nnnn
ecec
toto
rr
ss
located in Main Control Relay Box.located in Main Control Relay Box.
1. 1.
Plug in Plug in
the powthe pow
er pluger plug
..
2. 2.
PlPl
acac
e e
thth
ee
 On- On-
Off Off
SwitSwit
chch
 (Cab  (Cab
ComCom
manman
d)d)
andand
Run-Run-
-Stop -Stop
switchswitch
 to  to
ON ON
popo
sisi
tiotio
n n
anan
d d
prpr
eses
s s
thethe
Standby KeyStandby Key
. .
The The
micmic
roprop
rocroc
essess
or or
wilwil
l l
perper
form aform a
self-test (all display messages will appear in displayself-test (all display messages will appear in display
window). Then setpoint and box temperature will bewindow). Then setpoint and box temperature will be
displayed.displayed.
“NO POWER” will be displayed if unit is switch to“NO POWER” will be displayed if unit is switch to
standby and power plug not plugged in.standby and power plug not plugged in.
3. 3.
ChCh
ecec
kk
forfor
prpr
opop
erer
momo
tortor
roro
tattat
ioio
n.n.
CoCo
ndnd
enen
sese
rr
aiai
rr
mumu
stst
bebe
dradra
wnwn
inin
toto
unun
itit
(se(se
ee
inin
didi
caca
tintin
gflgfl
agag
onon
frofro
nt nt
grigri
llll
e).e).
TT
oo
revereve
rserse
rotarota
tiontion
,,
stopstop
uniuni
t,t,
disdis
concon
necnec
tt
powpow
erer
cordcord
and change polarity of plug.and change polarity of plug.
3.4 3.4
COMCOM
PP
ARAR
TMENTMEN
T T
OPEOPE
RARA
TIONTION
3.3.
4.4.
1 1
OpeOpe
rara
titi
on on
witwit
h h
caca
b b
comcom
mama
ndnd
a. a.
StaSta
rtirti
ng the unitng the unit
CoCo
mpmp
lele
te te
the the
prpr
e-te-t
riri
p p
inin
spsp
ecec
tiotio
n n
dede
scsc
ribrib
ed ed
in in
thethe
previous section.previous section.
SS
Road Road
operationoperation
1.1.
2.2.
3.3.
1. 1.
PlaPla
ce the RUce the RU
N/STN/ST
OP switOP swit
ch (O/I) to the Rch (O/I) to the R
UNUN
positiopositio
n n
(I)(I)
2. 2.
Press thPress th
e ROAD oe ROAD o
peratioperatio
n key n key
(only i(only i
f the unf the un
itit
has been previously used in standby mode).has been previously used in standby mode).
3. 3.
Place either one, Place either one,
two or two or
three compartmenthree compartmen
tsts
OFF/ON switches to ON (I)OFF/ON switches to ON (I)
4. 4.
TheThe
n, thn, th
e une un
it wiit wi
ll :ll :
--
perform a complete diaperform a complete dia
gnostic chegnostic che
ck on theck on the
microprocessor controllermicroprocessor controller
--
pre-hepre-he
at for the required amounat for the required amoun
t of tt of t
ime baseime base
dd
on the engine temperatureon the engine temperature
--
 starts automatically starts automatically
SS
On On
StandbyStandby
1.1.
2.2.
3.3.
CAUTIONCAUTION
BeBe
cece
rtrt
aiai
n thatn that
thethe
uniuni
tt
isis
concon
nene
ctct
ed toed to
an an
appropriappropri
ate power ate power
source.source.
1. 1.
PlaPla
ce the RUce the RU
N/STN/ST
OP switOP swit
ch (O/I) to the Rch (O/I) to the R
UNUN
positiopositio
n n
(I)(I)
2. 2.
Press Press
the STthe ST
ANDBY oANDBY o
peratiperati
on keon ke
yy
3.3.
Place eiPlace ei
ther one, two or three comther one, two or three com
partmenpartmen
tsts
OFF/ON switches to ON (I)OFF/ON switches to ON (I)
4. 4.
Then, the unThen, the un
it will begit will beg
in to run on ein to run on e
lectric polectric po
werwer
..