Cerber C612 - Event Reporting Codes Configuration

49
Ev.codes S:052
C0000000000
Ev.codes S:053
C00000000
Ev.codes S :054
B00000000
[44]
Pulse on guardian round OK
* The card has to be assigned to one user code that has the “Card controls access
controlPGM types” right (3
rd
right in the 3
rd
set of rights) enabled.
Section [052]: Event Reporting Codes in 4x2 Format regarding: Arming by User / Keyswitch Arming / “Arming by
PC” / “Timed Autoarming” / Inactivity Autoarming / Away Quick Arming
Enter 1 digit for “arming by user” code and 5 groups of 2 digits (HEX digits may be used), one group for each reporting event.
The keypad buzzer will sound 3 beeps after each digit group and 6 beeps after the last digit. Then the panel exits the section and will wait for a new command.
To exit the “main programming menu”, press [#] key.
Notes:
 If one event code isn’t to be reported to CS, the group (digit) which corresponds to the event will be set as [00] value (or as [0] value).
 If one event code should keep its value previously set, press [#] key instead of the corresponding group (digit).
 First digit specific for “arming by user” event will be used by the panel to generate the event code for transmission to the “central station” in 4x2 formats (4 account digits + 2 event digits).
So, in order to get the 2 event digits, the panel will automatic add to this specific digit the corresponding digit of the user number (for all users from 15 to 45 the identifying
digit of user number will be either “F” or modulo 16, according to the corresponding flag programming from section [032]).
Section [053]: Event Reporting Codes in 4x2 Format regarding: “Stay Arming by User” / “Stay Keyswitch Arming” /
“Quick Stay or Instant Stay Arming” / “Partial arming” / “Fail to autoarm”
Enter 1 digit for “stay arming by user code” and 4 groups of 2 digits (HEX digits may be used), one group for each reporting event.
The keypad buzzer will sound 3 beeps after each group and 6 beeps after the last digit. Then the panel exits the section and will wait for a new command.
To exit the “main programming menu”, press [#] key.
Notes:
1. If one event code should keep its value previously set, press [#] key instead of the corresponding group.
2. If one event code isn’t to be reported to CS, the group (digit) which corresponds to the event will be set as [00] value (or as [0] value).
3. The digit specific for “stay arming by user” event will be used by the panel to generate the event code for transmission to the “central station” in 4x2 formats (4 account digits + 2 event
digits). So, in order to get the 2 event digits, the panel will automatic add to this specific digit the corresponding digit of the user number (for all users from 15 to 45 the
identifying digit of user number will be either “F” or modulo 16, according to the corresponding flag programming from section [032]).
Section [054]: Event Reporting Codes in 4x2 Format regarding: “Disarming by User / “Keyswitch Disarming /
“Remote disarming by PC” / “Timed Autodisarming” / “Timed Autoarming Stopping”
Enter 1 digit for “disarming by user” code and 4 groups of 2 digits (HEX digits may be used), one group for each reporting event.
The keypad buzzer will sound 3 beeps after each digit group and 6 beeps after the last digit. Then the panel exits the section and will wait for a new command.
To exit the “main programming menu”, press [#] key.
Notes:
1. “Stopped autoarming” code will be transmitted to CS by the panel, if during the 3 minutes before autoarming, while the keypad buzzer is warning that the system will auto arm by time,
autoarming is stopped by any valid user code.
2. The time for audible warnings before autoarming is fixed at 3 minutes.
3. If one event code should keep its value previously set, press [#] key instead of the corresponding group (digit).
4. If one event code isn’t to be reported to CS, the group (digit) which corresponds to the event will be set as [00] value (or as [0] value).