6-4626
Shut-o Handle
Mango de cierre
Poignée du robinet
WARNING
Parts, Piezas, Pièces
6-6136
Hose
Manguera
Tuyau
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-1925
1. Hose to Tank
2. Nozzle
3. Pre-Use Check
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overll to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
5. Pressurizing and Spraying
7. Care, Storage and Maintenance
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions?
Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
¡Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin.
Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas?
No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ?
Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
010529-17 (A) R0116
6. To Release Pressure
1) Do: With pump facing away, turn locked handle counterclockwise until air begins to escape. Stop turning handle
when you hear air escaping.
2) Do: Stay away from the sprayer until all air has escaped.
Make sure hose is pushed all
the way to the tank. Make sure
hose clamp is tight and below
the hose barb. Turn clockwise
with a screwdriver to tighten.
Hose Barb
1A
8. Troubleshooting
-
Tank pressurizes but does not spray.
WARNING:
Release pressure in tank before troubleshooting.
Clean Nozzle Assembly (Fig. 8E-8F)
-Remove housing. Remove lter. Clean and re-assemble
Clean shut-off (Fig. 8A- 8D)
Pump until you feel
resistance.
Turn handle clockwise
to tighten.Push handle
down, turn 1/4 turn
counterclockwise to
release.
Push handle, down, turn
1/4 turn clockwise to
lock. Begin spraying. Re-
pump sprayer as required
to maintain spray force.
Adjust spray pattern by
turning nozzle cap. Do
not turn cap more than 2
turns or cap may come o
allowing spray material to
spray back on you.
5A 5B 5C 5D
6-7749 Extension wand
Vara de extensión
Rallonge
Attach nozzle to shut-o handle or extension wand.
6-4824
Fan Nozzle Pack
Paquete de boquilla a chorro
Ensamble de buse à jet éventail
Insert Filter. Insert O-ring.
Insert appropriate nozzle
into cap.
Attach cap with nozzle to end
of housing.
2. Cap
1. Nozzle
4. Filter
5. Housing
3. O-ring
6. Shut-o or Wand
Red,
Fine spray for
ner washes
Blue,
Medium
spray for
sealers
Yellow,
Course spray
for semi- trans-
parent stains
2C 2D
2E 2F
2A 2B
2G
2H
8E 8F
Sk-1154-1
WARNING: Improper use or failure to follow instructions can result in explosive failure causing
serious eye or other injury. For safe use of this product you must read and follow all instructions. Do not
leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion.
Do not store or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants
and full foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.
Never stand with face or body over top of tank when pumping or loosening pump to prevent ejecting pump
assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means other than
the original pump. Do not attempt to modify this sprayer. Replace parts only with manufacturer’s original
parts. Never spray ammable, caustic, acidic, chlorine, bleach or other corrosive solutions or heat,
pressure, or gas producing chemicals. Always read and follow chemical manufacturer’s instructions
before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace hose
before using. Replace with original manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for signs of
deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and could result in
explosive bursting under pressure. If any of these signs are found, discard tank immediately and replace. Do not attempt
to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20 strokes and
inspect for leaks).
5) Do: Direct shut-o away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with Filling,
Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and ttings for rust, corrosion and pitting. If any of these
conditions are found, replace aected part with original manufacturer’s part before using.
1) Do: Rinse tank thoroughly with water only, empty, rell with water. Follow Filling, Pressurizing and Spraying
Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle are thoroughly rinsed with
water after each use.
2) Do: Open shut-o and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
Pull handle straight
up.
Insert notches from
underside of handle
into plunger grooves
and turn counter-
clockwise.
Tighten plunger clockwise until
ush to top of shut-o body. Do
not over-tighten or unit may not
spray. Slide forks under plunger,
push handle down until it snaps
into place.
8A 8B
Handle
8D
Plunger ush
with body
Remove plunger, diaphragm and
spring. Wash diaphragm with
mild detergent. Reassemble:
Hold shut-o upright as shown,
place spring in hole, place
diaphragm on top of spring.
Reassemble plunger and tighten.
8C
Plunger
Spring
Diaphragm
P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458 www.chapinmfg.com
WARNING:
is product contains chemicals, including lead, known to the state of California to
cause birth defects and other reproductive harm. Wash hands after handling.
To Next Page
Need help?
General
