Chauvet DJ HURRICANE 1800 FLEX User Manual (English)

Other manuals for Chauvet DJ HURRICANE 1800 FLEX

Questions and Answers:

J
Jason SmithJul 27, 2025
Why Chauvet DJ Fog Machine has no output?
- W
  williamjonesJul 27, 2025
  If your Chauvet DJ Fog Machine has no output or short output, several factors could be at play. First, the heater may still be warming up; allow up to 10 minutes for complete warm-up. An air bubble in the fluid line could also be the culprit; let the product warm up fully. You can also try turning the fog machine 45° to help the fluid flow or power it off for 5 seconds, then back on, repeating up to 10 times. Ensure you're using the correct CHAUVET water-based fog fluid; if not, clean the machine with CHAUVET® FCQ before refilling.
L
Lauren CarlsonJul 31, 2025
What to do if Chauvet DJ Fog Machine does not power up?
- S
  Sarah LoweryJul 31, 2025
  If your Chauvet DJ Fog Machine doesn't power up, begin by checking the power outlet and trying another one. Inspect the power cord for any looseness or damage. Also, check the fuse and replace it with a new one of the same type and rating if it's blown.
B
brian92Aug 4, 2025
How to fix Chauvet DJ Fog Machine spitting fluid?
- K
  Katherine ThompsonAug 4, 2025
  If your Chauvet DJ Fog Machine is spitting fluid, the issue might be due to incorrect fluid. Clean the machine thoroughly with CHAUVET® FCQ and refill it with CHAUVET® water-based fog fluid.
J
Jeffrey PhillipsAug 9, 2025
Why does Chauvet DJ Fog Machine circuit breaker keep blowing?
- T
  Tyler ShermanAug 9, 2025
  If the circuit breaker or fuse keeps blowing in your Chauvet DJ Fog Machine, it could be due to an excessive load on the circuit. Ensure the total load doesn't exceed the breaker's or fuse's recommended capacity. Alternatively, there might be a short circuit along the power lines, so inspect the power lines and cords for any damage.
C
Caroline StevensAug 13, 2025
What to do if Chauvet DJ Fog Machine does not respond to DMX?
- C
  Chase BellAug 13, 2025
  If your Chauvet DJ Fog Machine isn't responding to DMX, verify the starting address on the product is correctly set. Also, check the DMX controller's polarity setting and ensure it's correct. Finally, inspect the DMX cable entering the unit for any looseness or damage.
S
Sarah TaylorAug 17, 2025
How to troubleshoot intermittent DMX problems with Chauvet DJ Fog Machine?
- J
  Jason MillsAug 17, 2025
  For intermittent DMX problems with your Chauvet DJ Fog Machine, first ensure you are using DMX-compatible cables; replace any non-DMX cables. Keep DMX cables away from AC wires or radio equipment to avoid interference. If the DMX cable is too long, use a shorter cable or install an optically coupled DMX amplifier before the product experiencing issues. Finally, make sure a terminator is connected.
A
Andrea HughesAug 21, 2025
What to do if Chauvet DJ Fog Machine shows false sensor reading?
- C
  Charles ReedAug 21, 2025
  To address false sensor readings (priming) on your Chauvet DJ Fog Machine, ensure the fluid tank is full. While the unit is operating, remove (but don't disconnect) the fluid tank and tilt the machine at a 45° angle. Alternatively, pinch the fluid line for 3-5 seconds to create a vacuum, then release. You can also allow the unit to reach operating temperature, set the output to maximum, and power cycle it 1-2 times until the fluid reaches the sensor and the blue indicator light stops flashing. Also, ensure that you use the correct CHAUVET® water-based fog fluid.