EasyManua.ls Logo

Chrysler 1991 - ACCELERATION; DECELERATION

Chrysler 1991
147 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
FUEL
SYSTEM
14 - 7
when
the vehicle is in overdrive, the transmission
will
be downshifted. The transmission thermo-switch
opens
at
134°C
(273°F).
The thermo-switch
will
close
once
the transmission
fluid
temperature drops to
116°C
(240°F).
The engine controller
will
turn
on the water-in-
fuel
lamp if a signal is received
from
the water-in-
fuel
sensor.
ACCELERATION
The vehicle distance
(speed)
sensor
and throttle po-
sition
sensor
inputs are used to control transmission
overdrive
operation.
If the coolant temperature switch is open, the
transmission
will
not be allowed to enter overdrive
(automatic transmission). The switch
opens
when
coolant temperature is below 16°C
(60°F).
If intake
manifold
air temperature is below 12°C
(54°F),
the KSB solenoid
will
be energized through
the air temperature switch. The solenoid remains en-
ergized
until
the air temperature switch
opens.
The
switch
opens
when intake
manifold
air temperature
is
above 16°C
(60°F).
If the transmission thermo-switch is open, the
transmission
will
not be allowed to enter into over-
drive
(automatic transmission). If the switch
opens
when
the vehicle is in overdrive, the transmission
will
be downshifted. The transmission thermo-switch
opens
at
134°C
(273°F).
The thermo-switch
will
close
once
transmission
fluid
temperature drops to 116°C
(240°F).
If the
speed
control system
resume/accelerate
func-
tion
is being used, the engine controller
will
only
al-
low
the vehicle to
accelerate
at a predetermined rate.
If
a
speed
control has
been
set and the resume/accel-
erate
button is momentarily pushed in, the engine
controller
will
increase
vehicle
speed
by two miles
per hour.
If
the
brakes
are applied, the engine controller
will
disable the
speed
control.
DECELERATION
The vehicle distance
(speed)
sensor
and throttle po-
sition
sensor
inputs are used to control transmission
overdrive
operation.
If the coolant temperature switch is open, the
transmission
will
not be allowed to enter overdrive
(automatic transmission). The switch
opens
when
coolant temperature is below 16°C
(60°F).
If the transmission thermo-switch is open, the
transmission
will
not be allowed to enter into over-
drive
(automatic transmission). If the switch
opens
when
the vehicle is in overdrive, the transmission
will
be downshifted. The transmission thermo-switch
opens
at
134°C
(273°F).
The thermo-switch
will
close
once
transmission
fluid
temperature drops to 116°C
(240°F).
If intake
manifold
air temperature is below 12°C
(54°F),
the KSB solenoid
will
be energized through
the air temperature switch. The solenoid remains en-
ergized
until
the air temperature switch
opens.
The
switch
opens
when intake
manifold
air temperature
is
above 16°C
(60°F).
If the
speed
control system
coast/set
function
is be-
ing
used, the engine controller
will
only
allow
the ve-
hicle
to
decelerate
at a predetermined rate. If the
coast/set
switch is pushed
while
the system is operat-
ing,
the controller
will
set
speed
control to the
rate
the vehicle is traveling at when the switch is re-
leased.
If
the
brakes
are applied, the engine controller
will
disable the
speed
control.
IGNITION
SWITCH
OFF
When the
ignition
switch is turned to the off posi-
tion,
the engine controller
still
receives battery
volt-
age through the battery input. Battery voltage is
needed
to
keep
engine controller memory alive. The
memory
stores
fault
messages
and the TPS value
from
the previous Key-on.

Related product manuals