Cisco 8832 Administration Guide

AP ConfigurationCisco IP Phone
Configuration
CCKMWEP
802.1xEAP-TLSEAP-TLS
CCKMTKIPWPA
FT, CCKMAESWPA2
CCKMWEP
802.1xPEAP-MSCHAPV2PEAP-MSCHAPV2
CCKMTKIPWPA
FT, CCKMAESWPA2
For more information about configuring authentication and encryption schemes on APs, see the Cisco Aironet
Configuration Guide for your model and release under the following URL:
http://www.cisco.com/cisco/web/psa/configure.html?mode=prod&level0=278875243
Wireless LAN Security
Cisco phones that support Wi-Fi have more security requirements and require extra configuration. These extra
steps include installing certificates and setting up security on the phones and on the Cisco Unified
Communications Manager.
For additional information, see Security Guide for Cisco Unified Communications Manager.
Cisco IP Phone Administration Page
Cisco phones that support Wi-Fi have special web pages that are different from the pages for other phones.
You use these special web pages for phone security configuration when Simple Certificate Enrollment Protocol
(SCEP) is not available. Use these pages to manually install security certificates on a phone, to download a
security certificate, or to manually configure the phone date and time.
These web pages also show the same information that you see on other phone web pages, including device
information, network setup, logs, and statistical information.
Configure the Administration Page for Phone
The administration web page is enabled when the phone ships from the factory and the password is set to
Cisco. But if a phone registers with Cisco Unified Communications Manager, the administration web page
must be enabled and a new password configured.
Enable this web page and set the sign-in credentials before you use the web page for the first time after the
phone has registered.
Once enabled, the administration web page is accessible at HTTPS port 8443 (https://x.x.x.x:8443,
where x.x.x.x is a phone IP address).
Before you begin
Decide on a password before you enable the administration web page. The password can be any combination
of letters or numbers, but it must be between 8 and 127 characters in length.
Your username is permanently set to admin.
Cisco IP Conference Phone 8832 Administration Guide for Cisco Unified Communications Manager
79
Cisco IP Conference Phone Administration
Wireless LAN Security

Cisco 8832 Specifications

General

Control type	Buttons
Display type	LCD
Product type	IP conference phone
Voice codecs	G.711a, G.711u, G.722, G.729A, G.729ab, OPUS, iLBC
Certification	CE Markings per directives 2014/30/EU and 2014/53/EU and 2014/35/EU \u2028 \u2028 UL 60950 Second Edition \u2028 CAN/CSA-C22.2 No. 60950 Second Edition \u2028 EN 60950 Second Edition (including A11 and A12) IEC 60950 Second Edition (including A11 and A12) EN 60950-1 IEC 60950-1 AS/NZS 60950.1 47CFR Part 15 (CFR 47) Class B AS/NZS CISPR32 Class B \u2028 CISPR32 \u2028Class B EN55032 \u2028 Class B EN 300 386 ICES003 Class B \u2028 VCCI Class B \u2028 EN61000-3-2 \u2028 EN61000-3-3 \u2028 EN61000-4-2 IEC61000-4-2 EN61000-4-3 IEC61000-4-3 EN61000-4-6 IEC61000-4-6 KN22 Class B \u2028 EN55024 \u2028 CISPR24 \u2028 KN24 Armadillo Light AS/ACIF S004 NZPTC220
Product color	Charcoal
Frequency range	100 - 20000 Hz
Built-in display	Yes
Display diagonal	3.9 \
Languages support	ARA, BUL, CAT, CHI (SIMPL), CHI (TR), CZE, DAN, DEU, DUT, ENG, ESP, EST, FIN, FRE, GRE, HEB, HUN, ITA, JPN, KOR, LAT, LIT, NOR, POL, POR, RUM, RUS, SER, SLK, SLV, SWE, TUR, UKR
Display resolution	480 x 128 pixels
Security algorithms	EAP-FAST, EAP-TLS, SHA-256, SSH
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet interface type	Fast Ethernet
Supported network protocols	IPv4, IPv6, SIP, SDP, UDP, DHCP, GARP, TFTP, HTTPS, RTP, RTCP, Cisco Discovery Protocol, LLDP
Cables included	USB
Storage temperature (T-T)	-10 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	10 - 95 %
Operating relative humidity (H-H)	10 - 90 %
USB connector type	USB Type-C
RJ-45 ports quantity	1

Weight and Dimensions

Width	278 mm
Height	61 mm
Weight	1850 g