5/11
Connecting/disconnecting the smartphone
Checking connection status
1
Change the mode to [TME] or [L-TM] (page 2) and push the
crown in to position
0
.
2
Press and release the lower right button
A
repeatedly until
the function hand indicates connection status (ON/OFF).
24 60
6
S
M
T
W
T
F
S
ON
ON
OFF
A
L
M
M
T
E
M
T
E
L
A
M
L
A
M
H
C
R
T
L
-
M
T
L
-
M
H
C
R
CALL
INFO
ACT
LL
60
30
S
M
T
W
T
F
S
ON
OFF
ON
OFF
A
L
M
Connection
status
Connection status indication
The function hand automatically indicates connection status (ON/OFF) as the
connection status between the watch and the smartphone changes.
ON OFF
60
30
S
M
T
W
T
F
S
ON
OFF
ON
OFF
A
L
M
60
30
S
M
T
W
T
F
S
ON
OFF
ON
OFF
A
L
M
Connected Disconnected
Disconnecting
• Cancel the notification indication of the second hand before disconnecting (page
4
).
1
While connected, change the mode to [TME] or [L-TM] (page
2) and push the crown in to position
0
.
2
Press and hold the upper right button
B
for 4 seconds.
The second hand points “ACT (40-second position)” and, after
disconnection, the function hand points “OFF” of connection
status.
24 60
30
12
6
18
S
M
T
W
T
F
S
ON
OFF
ON
OFF
A
L
M
M
T
E
M
T
E
L
A
M
L
A
M
H
C
R
T
L
-
M
T
L
-
M
H
C
R
CALL
INFO
LL
60
30
M
T
W
T
F
S
ON
OFF
ON
OFF
A
L
M
Connecting
You can reconnect the watch to a disconnected smartphone.
• The watch cannot be connected with a non-registered smartphone (page
4
).
• See page
6
to connect the watch to another registered smartphone.
1
While disconnected, change the mode to [TME] or [L-TM] (page
2) and push the crown in to position
0
.
2
Press and release the upper right button
B
.
The second hand points “ACT (40-second position)” and, after
connection, the function hand points “ON” of connection status.
24 60
30
12
6
18
S
M
T
W
T
F
S
ON
OFF
ON
OFF
A
L
M
M
T
E
M
T
E
L
A
M
L
A
M
H
C
R
T
L
-
M
T
L
-
M
H
C
R
CALL
INFO
LL
60
30
S
M
T
W
T
F
S
ON
OFF
ON
OFF
A
L
M
CITIZEN Bluetooth Watch W770 Instruction manual
Registering a smartphone
• For registration, you have to operate both the watch and the smartphone.
• Be sure both the watch and smartphone are sufficiently charged. Especially, it is
important to check power reserve of the watch (page
3
) and charge it before
registration if the power reserve level is “1” or “0”.
• Registration operation on the watch must be completed within a certain period
of time. If about 30 seconds have elapsed before finishing operation, the watch
returns to normal movement.
<Operation on the smartphone>
1
Download the dedicated app “CITIZEN Bluetooth Watch” at an
app site and install it.
2
Start the dedicated app.
• Keep the app showing on the smartphone screen.
• Agree when a dialog appears to request your permission to use
Bluetooth connection.
<Operation of the watch>
3
Change the mode to [TME] or [L-TM] (page 2) and push the
crown in to position
0
.
4
Press and release the upper right button
B
.
The second hand points “ACT (40-second
position)” and registration starts.
• The smartphone will be connected if it
has already been registered before.
<On the smartphone>
5
“Connected” appears as registration is successful.
• It may take about 20 - 30 seconds to finish registration.
The watch and smartphone are connected as registration is
successful.
When registration is successful
The function hand of the watch will point “ON” of connection status and the
second hand returns to indicate the seconds.
24 60
30
12
6
18
S
M
T
W
T
F
S
ON
OFF
ON
OFF
A
L
M
M
T
E
M
T
E
L
A
M
L
A
M
H
C
R
T
L
-
M
T
L
-
M
H
C
R
CALL
INFO
LL
60
30
M
T
W
T
F
S
ON
OFF
ON
OFF
A
L
M
In the cases below, registration is not successful:
• The second hand of the watch points “LL (45-second position)”.
• The second hand of the watch points “ACT (40-second position” and returns to
indicate the seconds and the function hand does not point “ON” of connection
status.
12
A
L
M
M
T
E
M
T
E
L
A
M
L
A
H
C
R
T
L
-
T
L
-
M
ACT
LL