ClearWater CD-2000 - Page 16

16
OPTIONAL VACUUM BREAK INSTALLATION
Location
Selectasuitableverticalsurfacethatisaccessibleandincloseproximitytotheozonegeneratorandventurimanifoldonwhichto
mountthevacuumbreak.
Installation Steps
1. InstallthetwomountingClic
®
clampsprovidedontheverticalsurfacesothatthevacuumbreakwillbeinaverticalpositionand 
 theheightofthell/drainvalvettingwillbebelowtheleveloftheozonegeneratorbulkheadcheckvalve.Oneclampshould 
 belocateddirectlyabovethevacuumbreak’sbottomendcapandtheotherjustbelowthell/drainttingtee.
2. Installthetworeducerbushingsprovidedintotherisertee,oneintothesidetappingandtheotherintothetoptapping.
 Besuretouse2-3wrapsofTeon
®
tape on the male threads.
3. InstallthePVCballvalveprovidedintothereducerbushinginthesidetappingontherisertee.Besuretouse2-3wrapsof
 Teon
®
tapeonthemalethreads.Thisvalvecontrolstheamountofwaterthatisdrawnupintotherisertubebythesuction
 oftheventuri.Itcanalsobeusedtoisolatetheventurishouldacheckvalvefail.
4. Installthe90ºKynar
®
ttingprovidedintothereducerbushingonthetoptappingontherisertee.Besuretouse2-3  
 wrapsofTeon
®
tape on the male threads.
5. Placethetwo-inchdiameterwaterreservoirintothemountingClic
®
clampsandsecure.Checktomakesuretheheightofthe 
 ll/drainttingisbelowtheleveloftheozonegeneratorbulkheadcheckvalve.
6.Slidetherisertubeintothewaterreservoir.
7. Attachoneendofasuitablelengthof1/4”Teon
®
tubingprovidedtothe90ºKynar
®
compressionttingonthetopof  
 therisertee.Attachtheotherendofthetubingtothebulkheadcheckvalveonthebottomoftheozonegenerator.The  
 lengthofthetubingwilldependonthedistancebetweenthevacuumbreakandtheozonegenerator.
8. Initiatewaterowthroughthesystem(e.g.,startthecirculationpumporboosterpump)sowaterisowingthroughthe
 venturiinjector.Adjustthesuctionattheventuriwithahand-heldSCFHgauge,matchingtheairowtothecorrect
 specicationasoutlinedonpages17and18.
9. ClosethePVCballvalveontherisertee.Usingthestraightcompressionttingprovided,attachanothersuitablelength
 of1/4”Teon
®
tubingtotheoutletofthePVCballvalve.Attachtheotherendofthetubingtothecompressionttingonthe 
 venturicheckvalveassembly.
10. Turnthell/drainttingsotheopeningfacesupwardandaddwatertothewaterreservoiruntilitbeginstooverowoutofthe 
 ll/draintting.Nowturnthettingsotheopeningfacesdownward.
11. SlowlyopenthePVCballvalveontherisertee,allowingthewaterlevelintherisertubetorisetoalevelnocloserthantwo 
inches from the bottom of the riser tee.
12.Connectasuitablelengthofthe3/4”braidedtubingprovidedtothebarbedttingonthell/draintting.Makesure  
 theopenendofthetubinggoestosafe,properdrainageandthatthetubehasnoowrestrictions.
13.Runthesystemtoensurethewaterlevelintherisertubeisstabilized.
Note:Theproperwaterlevelmustbemaintainedinthewaterreservoir.Whenfull,thereservoircontainsabouttwicetheamount
ofwaterrequiredtolltherisertube,soitmustalwaysbekeptatleasthalffull.Aninsufcientwaterlevelwillresultinalossof
vacuum,preventingairowthroughtheozonegenerator.
Plumbing Connections - continued