13
12
Intro Operation Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
Caution Warning
Installation
Customer
Assistance
Operation
Intro Operation Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
Caution Warning
Installation
Customer
Assistance
LCD Display Function Setting
KEY BP Beep on (default): turn on beep
oF: turn off beep
ROG BP
Roger Beep Sound
oF, Tone settings 01 - 06
(End of transmission sound)
oF: (default) turn off
roger beep
VOX L
VOX Level (Sensitivity)
Level: 01 - 09
Default: 03
VOX T VOX Delay Time Level: 01 - 09
Default: 01
RF.GAIN RF Gain Control Levels
: 03, 06, 09 - 48
oF (default) RF gain off
TOTSET Time Out Timer oF, 01 - 10 minutes
Default: 05
PWRAUTO
Automatic Power On
on
(default): Auto power on
oF:
Manual power on
FW VER
Firmware Version
Displays 2-digit
Firmware Version
RESET
See Reset to Factory
Default Section (page 8)
Menu Options
Selecting Options from the Menu
Selecting the Menu
Intro Operation
Frequency Ranges
This unit features advanced Phase Lock Loop (PLL) circuitry providing
complete coverage of all 40 CB channels.
NOTE
All 40 channels support AM and FM operating modes.
CB
Channel
Channel Frequency
in MHz
1 26.965
2 26.975
3 26.985
4 27.005
5 27.015
6 27.025
7 27.035
8 27.055
9 27.065
10 27.075
11 27.085
12 27.105
13 27.115
14 27.125
15 27.135
16 27.155
17 27.165
18 27.175
19 27.185
20 27.205
CB
Channel
Channel Frequency
in MHz
21 27.215
22 27.225
23 27.255
24 27.235
25 27.245
26 27.265
27 27.275
28 27.285
29 27.295
30 27.305
31 27.315
32 27.325
33 27.335
34 27.345
35 27.355
36 27.365
37 27.375
38 27.385
39 27.395
40 27.405
Mode
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
Mode
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
AM/FM
1. Press and release the MENU button to enter the menu list.
2. Turn the POWER button or press the microphone UP or DN buttons to
choose the desired function.
3.
Press and release the POWER button to enter the setting for the desired
function. Once selected, the setting will blink on the LCD display.
4. Turn the POWER button clockwise or press the microphone UP or DN
buttons to select the desired setting.
5. Press and release the POWER button to confirm the setting and exit.
6. To exit the menu, press and hold the POWER button or press and hold
the microphone PTT switch or wait 10 seconds once the setting
selection has been confirmed.
Signal Strength Meter
The Signal Strength Meter indicates the received signal strength
from the antenna. The meter segments shown on the LCD increase
with signal strength.
TX Indicator
The TX Indicator appears when in transmit mode. In this mode,
the meter shows all bars at full output power.
Channel Frequency
Displays the current channel frequency.
Enable/Disable VOX
1. Push and hold the Push-To-Talk switch on the microphone, then
2. Push and release the MENU button.
3. This will both enable and disable the VOX function.
Scan
1.
Press and hold either the Channel UP or DOWN button (about 3
seconds) until SCAN is activated.
2. The radio will automatically scan all 40 Channels and stop on an
active channel. Press any key to end SCAN.
Reset to Factory Default
1. Press and hold the MENU button to enter the menu list.
2. Turn the POWER button or press the microphone UP or DN button to
choose the RESET setting.
3.
Press and release the POWER button to select. RESET will blink in
the display.
4. Press and hold the POWER button until RESET stops blinking.
5. Release the POWER button and the radio will automatically
reset to factory default settings.
To Next Page
Loading...
