Why CONTEC MEDICAL SYSTEMS Blood Pressure Monitor can not upload the measurement results to PC software?
The inability to upload measurement results to PC software may occur because the device is not powered on during uploading, resulting in a dark screen, or because the PC does not recognize the device. Ensure the screen is lit during the upload process. If the issue persists, try re-inserting the USB cable.
What to do if CONTEC MEDICAL SYSTEMS ABPM50 Blood Pressure Monitor displays 'Time out'?
If the CONTEC MEDICAL SYSTEMS Blood Pressure Monitor displays 'Time out', it could be due to a blocked or incorrectly connected tube, or a loose cuff. First, check the tube to ensure it is properly connected and not blocked. Then, make sure to wear the cuff correctly, ensuring it is snug but not too tight.
Why CONTEC MEDICAL SYSTEMS ABPM50 Blood Pressure Monitor shows weak signal?
A weak signal on the CONTEC MEDICAL SYSTEMS Blood Pressure Monitor is often due to the cuff being incorrectly positioned or too loose. Ensure the cuff is worn correctly and snugly around your arm.
What to do if CONTEC MEDICAL SYSTEMS ABPM50 cuff has gas leakage?
If you notice gas leakage from the CONTEC MEDICAL SYSTEMS Blood Pressure Monitor cuff, it's likely that the connection between the tube and the cuff isn't tight enough. Inspect the tube connection and ensure it is securely attached. Additionally, make sure the cuff is wrapped tightly around your arm to prevent leaks.
What to do if CONTEC MEDICAL SYSTEMS ABPM50 displays 'Over the pressure range'?
If the CONTEC MEDICAL SYSTEMS Blood Pressure Monitor displays 'Over the pressure range', this may be due to a blocked or constricted tube. Check the tube to ensure it is not blocked or pinched.
Why CONTEC MEDICAL SYSTEMS ABPM50 Blood Pressure Monitor air valve can not deflate?
If the air valve on your CONTEC MEDICAL SYSTEMS Blood Pressure Monitor isn't deflating, there are a couple of potential reasons. It could be that the power line to the air valve is disconnected, or the air tube is blocked. Check the power line of the air valve to ensure it's properly connected. Also, inspect the air tube to see if it's blocked.
What to do if CONTEC MEDICAL SYSTEMS Blood Pressure Monitor air valve leakage?
If the air valve is leaking on your CONTEC MEDICAL SYSTEMS Blood Pressure Monitor, the power line of the air valve may be disconnected. Check the power line of air valve. Also, check whether the air tube is connected tightly or not.
What to do if CONTEC MEDICAL SYSTEMS Blood Pressure Monitor air pump can not start?
If the air pump on your CONTEC MEDICAL SYSTEMS Blood Pressure Monitor fails to start, it might be due to the power line of the air pump being disconnected from the BP board. To resolve this, open the device shell and check the power line of the air pump to ensure it's properly connected.
How to fix CONTEC MEDICAL SYSTEMS ABPM50 Blood Pressure Monitor when the screen is dark and the indicator light does not flash?
If the indicator light does not flash and the screen is dark when you long press the power-on button on your CONTEC MEDICAL SYSTEMS Blood Pressure Monitor, there could be several reasons: the battery capacity might be insufficient or the polarity is reversed, the power line could be disconnected, or the BP board and LCD board might not be well-connected. Here's what you can do: 1. Check the capacity and polarity of the battery. 2. Open the shell and check the power line. 3. Reconnect the BP board and LCD board.
Device is used for BP monitoring in adults, children, and neonates, storing records.
Details blood pressure and pulse rate measurement methods, ranges, resolution, and accuracy.
Describes the top interface of the device, including the NIBP cuff interface.
Outlines temperature, humidity, altitude, and supply voltage requirements for device operation.
Explains the composition of the device's hardware modules, including BP and LCD boards.
Details the BP board's block diagram and interface definitions for power, pump, fast, and slow valves.
Details the LCD board's block diagram and interface definitions for communication with the MCU.
Covers routine checks for appearance, main components, and basic functions of the device.
Specifies requirements for product shell smoothness, color, and component assembly.
Describes how to test device functions like power button operation and automatic measurement.
Details the inspection process for blood pressure measurement accuracy using a simulator.
Provides instructions for disassembling the device, starting with the shells.
Step-by-step guide to removing the device's back shell after removing screws.
Instructions for removing the BP board after dismantling screws.
Details how to remove the air pump and air valve from the BP board.
Guides users to reassemble the device by following the reverse order of disassembly.
General| Model | ABPM50 |
|---|---|
| Type | Ambulatory Blood Pressure Monitor |
| Measurement Method | Oscillometric |
| Accuracy (Pressure) | ±3 mmHg |
| Accuracy (Pulse Rate) | ±5% of reading |
| Resolution | 1 mmHg |
| Overpressure Protection | Yes |
| Data Storage | Yes |
| Memory Capacity | Up to 300 measurements |
| Display | LCD |
| Software | Yes (PC software for data analysis) |
| Cuff Size | Small, Medium, Large |
| Weight | Approx. 300 g |
| Operating Conditions (Temperature) | 10°C to 40°C |
| Operating Conditions (Humidity) | 15%~85% |
| Storage Conditions (Temperature) | -20 to 60 °C |
| Storage Conditions (Humidity) | 10%~95% |
| Measurement Range (Pressure) | 0 to 280 mmHg |
| Measurement Range (Pulse Rate) | 40 to 180 bpm |
To Next Page