Continental Refrigerator 115/60/1 User Manual (English)

Questions and Answers:

W
wwilliamsAug 1, 2025
Why does my Continental Refrigerator condensing unit run for prolonged periods?
- D
  Daniel JohnsonAug 2, 2025
  Your Continental Refrigerator condensing unit might run for extended durations due to several reasons. It could be caused by a shortage of refrigerant, in which case you should fix the leak, evacuate, and recharge the system. Alternatively, the control contacts may be stuck closed, requiring cleaning or replacement. Other potential causes include excessive heat load, frequent door openings, an iced evaporator coil (which needs defrosting), a restriction in the refrigeration system (which needs to be located and removed), a dirty condenser coil (which needs cleaning), or a clogged filter drier (which needs replacement, evacuation, and recharging).
C
curtisrichardsonAug 6, 2025
What to do if Continental Refrigerator condensing unit will not start, but hums and trips on overload protector?
- J
  jeffreymitchellAug 6, 2025
  If your Continental Refrigerator condensing unit hums but trips the overload protector, it could be due to several issues. First, check the wiring against the diagram to ensure it's properly wired. Low voltage to the unit could also be the cause, so determine the reason and correct it. Other potential causes include a defective starting capacitor or a relay failing to close, both of which would need to be replaced. In more serious cases, the compressor motor might have a shorted or open winding, or there could be internal mechanical trouble in the compressor, both requiring compressor replacement. Finally, insufficient air supply could be the culprit; clear the condenser and allow the compressor to cool down.
E
eric74Aug 11, 2025
What causes short cycles on overload protector in Continental Refrigerator condensing unit?
- G
  Gregory JonesAug 11, 2025
  Short cycling of your Continental Refrigerator condensing unit on the overload protector can stem from multiple causes. There might be additional current passing through the overload protector, so check the wire diagram and look for added components connected to the wrong side. Low voltage to the unit can also cause this issue, so determine the reason and correct it. A defective overload protector or run capacitor could also be responsible, requiring checking the current and replacing the protector or determining the reason and replacing the capacitor, respectively. Furthermore, excessive discharge or suction pressure, or insufficient air supply could be the reason. Check ventilation and for restrictions, or clear the condenser and allow the compressor to cool down.
F
fischeralexAug 16, 2025
How to fix a Continental Refrigerator condensing unit that won't start and has no hum?
- L
  lopezanaAug 16, 2025
  If your Continental Refrigerator condensing unit won't start and there's no hum, several issues could be the cause. Ensure the line is connected and the switch is closed. If a fuse is removed or blown, replace it. If the overload protector is blown, determine the reason and correct or replace it. If the control is 'Off' due to a cold location, relocate the control. If the control is stuck in the open position, repair or replace it. Finally, check the wiring against the diagram to ensure it's correct and not loose.
L
Lisa ReyesAug 21, 2025
Why does Continental Refrigerator condensing unit start, but fail to switch off of “start” winding?
- J
  Jennifer MendozaAug 22, 2025
  If your Continental Refrigerator condensing unit starts but fails to switch off the 'start' winding, several factors could be responsible. Check the wiring against the diagram to ensure it is properly wired. Low voltage to the unit could also be a cause, so determine the reason and correct it. Other potential issues include a relay failing to open or a defective run capacitor, both requiring determination of the reason and replacement. Excessively high discharge pressure, potentially due to a faulty discharge shut-off valve or overcharge, could also be the reason. In more severe cases, the compressor motor might have a shorted or open winding, or there could be internal mechanical trouble in the compressor, both necessitating compressor replacement.
T
Timothy WilliamsAug 27, 2025
Why does Continental Refrigerator condensing unit run, but short cycles on different components?
- M
  Mandy LopezAug 27, 2025
  If your Continental Refrigerator condensing unit runs but short cycles, the issue could stem from several components. If it short cycles on the overload protector, check the current and replace the protector if necessary. For short cycling on the thermostat, widen the differential setting. If it short cycles on the high-pressure cut-out due to insufficient air supply, check the air supply to the condenser. If it is due to overcharge or air in the system, evacuate and recharge. For short cycling on the low-pressure cut-out due to a valve leak, replace, evacuate, and recharge. If it is due to undercharge, evacuate and recharge. If the short cycling is due to a restriction in the expansion device, replace the expansion device.

Continental Refrigerator 115/60/1 Specifications

General

Brand	Continental Refrigerator
Model	115/60/1
Category	Refrigerator
Language	English

Summary

Receiving Your New Continental Refrigerator

General Information and Operating Facts

Serial Data Tag Identification

Details the location and importance of the unit's serial data tag for product identification.

Model Components Overview

Identifies key components of standard and designer line reach-in refrigerators or freezers.

Uncrating Your New Unit

Installation and Location Guidelines

Ventilation Requirements

Ensures proper airflow for efficient operation and longevity of the refrigeration system.

Installing Casters and Leveling

Instructions for securely attaching casters and ensuring the unit is stable and level.

Floor Load Considerations

Guidance on ensuring the installation floor can support the total weight of the unit and product.

Installing Legs and Leveling

Steps for attaching and adjusting the unit's legs for proper leveling.

Roll-In and Roll-Thru Model Installation

Specific instructions for installing units designed for rolling carts.

Site Preparation

Ensuring the installation area is prepared, level, and clean for optimal unit placement.

Cabinet Leveling and Shimming

Detailed steps for achieving a perfectly level and plumb cabinet installation.

Cabinet and Door Adjustment

Procedures for aligning cabinet components and doors for proper sealing.

Mounting Caster Support Plates

Instructions for installing optional heavy-duty plates for enhanced caster stability.

Installation of Tie-In Straps

Guidance for connecting multiple cabinets together for rigidity and stability.

Remote Set-Up and Installation Guidelines

Specific procedures for installing remote refrigeration systems and ensuring leak-tight connections.

Fish File Model Installation

Special installation considerations for fish file units, including drain requirements.

Condensate Removal Procedures

Interior Coil Models

Instructions for installing the electric condensate vaporizer system.

Top Mount Coil Models

Details on the self-contained hot air evaporating system for condensate.

Door and Hinge Maintenance

Door Removal and Adjustment

Steps for removing doors and adjusting them for proper alignment and sealing.

Hinge Removal and Replacement

Procedure for removing and reinstalling door hinges, including light switch considerations.

Re-Hinging Doors (Reach-Ins)

Instructions for field re-hinging doors, including electrical connections for lighting.

Sliding Glass Door Removal and Adjustment

Guidance on removing, cleaning, and adjusting sliding glass doors for proper operation.

Hinged Glass Door Removal and Adjustment

Steps for removing and adjusting hinged glass doors, including electrical cords.

Grill Removal and Cleaning

Removing Grill

Instructions on how to safely remove and reinstall the cabinet grill assembly.

Initial Cleaning Procedure

Recommended steps for thoroughly cleaning the interior surfaces before initial use.

Periodic Cleaning Procedure

Detailed steps for cleaning interior and exterior surfaces of the unit.

Cleaning Precautions

Warnings against using harsh chemicals or abrasive cleaners on unit surfaces.

Care and Cleaning of Stainless Steel

Specific guidelines for cleaning stainless steel to prevent corrosion and maintain finish.

Cleaning and Maintenance (Fish File Models)

Daily cleaning requirements for fish file models to prevent residue and odors.

Start-Up Procedure and Electrical Connections

Electrical Connections

Ensuring correct voltage and wiring connections for safe and proper operation.

GFI/GFCI Receptacles

Recommendations regarding the use of GFCI protection on unit power supplies.

Voltage Specific Connections

Guidelines for connecting 115V and 115/208-230V units to appropriate power sources.

Start-Up Checklist

A comprehensive checklist to verify all steps before initial unit operation.

Operation with Mechanical Thermostat

Dial Thermometer and Calibration

How to read and calibrate the dial thermometer for accurate temperature readings.

Digital Thermometer and Calibration

Instructions for calibrating the digital display for precise temperature indication.

System Operation and Adjustments

Anti-Condensate Control

Managing anti-condensate heaters for optimal moisture control and energy savings.

Refrigeration System and Adjustment

Understanding and adjusting the refrigeration system for desired cabinet temperatures.

Freezer System and Adjustment

Guidelines for operating and adjusting freezer systems for optimal food preservation.

Defrost Operation

Explanation of the automatic electric defrost system and its timing.

Warmer System and Adjustment

Operating instructions for warming cabinets to maintain food at safe holding temperatures.

Refrigeration System Configurations

Standard Reach-In Ceiling-Mount Evaporator

Description of the low-profile evaporator system located in the interior ceiling.

Top-Mount Plug Box Evaporator System

Details on the evaporator system housed in a top cabinet assembly.

Warmer System Configurations

Warmer with Axial Fans

Explanation of warmers with internal heating elements and axial fans for distribution.

Roll-In Warmer with Blower

Description of warmers with top-mounted heating elements and blowers for air circulation.

Operation with Electronic Control

Electronic Control Display and Buttons

Overview of the control panel, its display, and button functions.

Initial Sequence of Operation

Step-by-step guide for the unit's initial start-up sequence and operation.

How to Calibrate the Electronic Control

Procedure for calibrating the electronic control's temperature display.

How to Change the Set-Point

Instructions for adjusting the target temperature set-point for cooling or warming.

Advanced Electronic Control Functions

Anti-Condensate Control Adjustment

Managing the anti-condensate heaters via the electronic control.

Initiate Manual Defrost

Procedure for manually triggering an additional defrost cycle.

Change Defrost Interval

Adjusting the frequency of automatic defrost cycles.

High and Low Temperature Alarms

Setting and managing temperature alarm thresholds and delays.

Electronic Control Error Codes

Interpreting error codes displayed by the electronic control for diagnostics.

Interior Accessories and Product Loading

Shelving Installation

Guidance on installing shelves using pilaster strips and clips for proper airflow.

Product Loading Guidelines

Recommendations for distributing product to ensure optimal airflow and performance.

Safety Precautions and Maintenance

General Safety Precautions

Essential safety warnings regarding electrical hazards and equipment handling.

General Preventative Maintenance

Key maintenance tasks, especially condenser cleaning, for unit longevity.

Digital Thermometer with Alarm Features

Details on the thermometer's alarm functions, data logging, and battery backup.

Parts and Service Information

Placing a Service Call

Steps to follow and information required when requesting service.

Obtaining Replacement Parts Under Warranty

Procedure for requesting warranty replacement parts from the manufacturer.

Obtaining Replacement Compressor Under Warranty

Process for obtaining a warranty replacement for the compressor unit.

End-of-Life Disposal

Guidelines for the safe and environmentally responsible disposal of the equipment.

Optional Accessories

Pan Slide Assemblies

Information on available pan slide configurations and their installation.

Pan Slide Installation

Step-by-step guide for installing pan slide assemblies at desired heights.

Wire Pan Slide Racks

Details on wire rod pan slide racks and their attachment to cabinet walls.

Product Temperature Adjustment

Adjusting Program Settings

How to navigate and adjust various program settings on the control unit.

Fish File Model Operation

Loading and Storing Product

Guidelines for loading product with ice and maintaining optimal temperature.

Troubleshooting Guide

Refrigerator Wiring Diagrams

115/60/1 WD-R1 Wiring Diagram

Electrical schematic for a 115V refrigerator unit.

115/208-230/60/1 WD-R2 Wiring Diagram

Electrical schematic for a 115/208-230V refrigerator unit.

Glass Door Refrigerator 115/60/1 WD-R3 Wiring Diagram

Electrical schematic for a 115V glass door refrigerator unit.

Glass Door Refrigerator 115/208-230/60/1 WD-R4 Wiring Diagram

Electrical schematic for a 115/208-230V glass door refrigerator unit.

Electronic Control Refrigerator WD-R1-EC Wiring Diagram

Electrical schematic for a 115V refrigerator with electronic control.

Electronic Control Refrigerator WD-R2-EC Wiring Diagram

Electrical schematic for a 115/208-230V refrigerator with electronic control.

Glass Door Electronic Control Refrigerator WD-R3-EC Wiring Diagram

Electrical schematic for a 115V glass door refrigerator with electronic control.

Glass Door Electronic Control Refrigerator WD-R4-EC Wiring Diagram

Electrical schematic for a 115/208-230V glass door refrigerator with electronic control.

Freezer Wiring Diagrams

115/60/1 WD-F1 Wiring Diagram

Electrical schematic for a 115V freezer unit.

115/208-230/60/1 WD-F2 Wiring Diagram

Electrical schematic for a 115/208-230V freezer unit.

Glass Door Freezer 115/60/1 WD-F3 Wiring Diagram

Electrical schematic for a 115V glass door freezer unit.

Glass Door Freezer 115/208-230/60/1 WD-F4 Wiring Diagram

Electrical schematic for a 115/208-230V glass door freezer unit.

Electronic Control Freezer Wiring Diagrams

Freezer 115/60/1 W/ Split Electronic Control WD-F1-EC Wiring Diagram

Electrical schematic for a 115V freezer with split electronic control.

Freezer 115/208-230/60/1 W/ Split Electronic Control WD-F2-EC Wiring Diagram

Electrical schematic for a 115/208-230V freezer with split electronic control.

Glass Door Freezer 115/60/1 W/ Split Electronic Control WD-F3-EC Wiring Diagram

Electrical schematic for a 115V glass door freezer with split electronic control.

Glass Door Freezer 115/208-230/60/1 W/ Split Electronic Control WD-F4-EC Wiring Diagram

Electrical schematic for a 115/208-230V glass door freezer with split electronic control.

Warmer Wiring Diagrams

Self Contained Warmer 115/208-230/60/1 WD-W1 Wiring Diagram

Electrical schematic for a self-contained warmer with specific voltage configurations.

Self-Contained Warmer 115/208-230/60/1 WD-W2 Wiring Diagram

Electrical schematic for a warmer with mixed voltage and features.

Warranty Information

Three (3) Year Parts and Labor Warranty

Details the terms of the manufacturer's comprehensive three-year warranty.

Additional Two (2) Year Compressor Part Warranty

Specifies the extended warranty coverage for the sealed compressor unit.

Related product manuals

Continental Refrigerator SW48-10

2 pages

SW27-12M-FB

2 pages

Continental Refrigerator CPA43

2 pages

Continental Refrigerator 115/60/1 User Manual

Table of Contents

Questions and Answers:

Continental Refrigerator 115/60/1 Specifications

Summary

Receiving Your New Continental Refrigerator

General Information and Operating Facts

Serial Data Tag Identification

Model Components Overview

Uncrating Your New Unit

Installation and Location Guidelines

Ventilation Requirements

Installing Casters and Leveling

Floor Load Considerations

Installing Legs and Leveling

Roll-In and Roll-Thru Model Installation

Site Preparation

Cabinet Leveling and Shimming

Cabinet and Door Adjustment

Mounting Caster Support Plates

Installation of Tie-In Straps

Remote Set-Up and Installation Guidelines

Fish File Model Installation

Condensate Removal Procedures

Interior Coil Models

Top Mount Coil Models

Door and Hinge Maintenance

Door Removal and Adjustment

Hinge Removal and Replacement

Re-Hinging Doors (Reach-Ins)

Sliding Glass Door Removal and Adjustment

Hinged Glass Door Removal and Adjustment

Grill Removal and Cleaning

Removing Grill

Initial Cleaning Procedure

Periodic Cleaning Procedure

Cleaning Precautions

Care and Cleaning of Stainless Steel

Cleaning and Maintenance (Fish File Models)

Start-Up Procedure and Electrical Connections

Electrical Connections

GFI/GFCI Receptacles

Voltage Specific Connections

Start-Up Checklist

Operation with Mechanical Thermostat

Dial Thermometer and Calibration

Digital Thermometer and Calibration

System Operation and Adjustments

Anti-Condensate Control

Refrigeration System and Adjustment

Freezer System and Adjustment

Defrost Operation

Warmer System and Adjustment

Refrigeration System Configurations

Standard Reach-In Ceiling-Mount Evaporator

Top-Mount Plug Box Evaporator System

Warmer System Configurations

Warmer with Axial Fans

Roll-In Warmer with Blower

Operation with Electronic Control

Electronic Control Display and Buttons

Initial Sequence of Operation

How to Calibrate the Electronic Control

How to Change the Set-Point

Advanced Electronic Control Functions

Anti-Condensate Control Adjustment

Initiate Manual Defrost

Change Defrost Interval

High and Low Temperature Alarms

Electronic Control Error Codes

Interior Accessories and Product Loading

Shelving Installation

Product Loading Guidelines

Safety Precautions and Maintenance

General Safety Precautions

General Preventative Maintenance

Digital Thermometer with Alarm Features

Parts and Service Information

Placing a Service Call

Obtaining Replacement Parts Under Warranty