EasyManua.ls Logo

CycleOps SuperMagneto Pro - Trainer Setup; Attaching Your Bike to the Trainer

CycleOps SuperMagneto Pro
10 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
1
MONTAGE ET RÉGLAGE DE E L’APPAREIL D’ENTRAÎNEMENT
MONTAJE DEL APARATO DE ENTRENAMIENTO
1.1: Pour monter votre appareil, étendez ses pieds comme illustré ci-dessous,
puis posez-le sur une surface plane.
1.2: Tournez la molette pour régler le pied et mettre le cadre de niveau, comme
illustré ci-dessous.
1.1: Zuerst stellen Sie die Beine, wie unten dargestellt, aus. Dann stellen Sie den
Trainer auf eine ebene Fläche.
1.2: Drehen Sie das Stellrad, wie unten dargestellt, um das Bein anzupassen und
den Rahmen auszurichten.
1.1: Per impostare il rullo, estendere le gambe come mostrato qui sotto,
quindi collocare il rullo su una superficie piana.
1.2: Ruotare la rotella per regolare la gamba e stabilizzare il telaio come mostrato
qui sotto.
1.1: Om uw trainingstoestel te monteren, spreidt u eerst de benen van het toestel,
zoals hieronder afgebeeld. Vervolgens plaatst u het trainingstoestel op een effen
oppervlak.
1.2: Draai aan het duimwieltje om de benen aan te passen en het frame gelijk te
stellen, zoals hieronder afgebeeld.
1.1:レーナーを組み立るには、下図のに脚を拡げな面に
てます。
1.2:下図のにサムホールを回脚の高さを調節レームを平
にしす。
MONTAGE VAN UW TRAININGSTOESTEL
IMPOSTAZIONE RULLO
TRAINER SETUP
レーナーの設定方法
2
FIXATION DU VÉLO SUR L’APPAREIL D’ENTRAÎNEMENT
FIJACIÓN DE LA BICICLETA AL APARATO DE ENTRENAMIENTO
ATTACHING YOUR BIKE TO THE TRAINER
UW FIETS AAN HET TRAININGSTOESTEL BEVESTIGEN
MONTAGGIO DELLA BICICLETTA SUL RULLO
FAHRRAD AUF DEM TRAINER MONTIEREN
バイレーーへの取付け
2.1: L’appareil d’entraînement est conçu pour être utilisé avec la broche fournie.
Remplacez la broche de la roue arrière de votre vélo par celle fournie. Veillez à ce
que la poignée de desserrage rapide se trouve du côté gauche du vélo et soit
orientée vers le haut.
2.1: Der Trainer muss mit dem beiliegenden Schnellspanner verwendet werden.
Ersetzen Sie den Schnellspanner am Hinterrad Ihres Fahrrads durch den
beiliegenden Schnellspanner. Achten Sie darauf, dass sich der Schnellspannerhebel
auf der linken Seite des Fahrrads befindet und nach oben zeigt.
2.1: Il rullo è progettato per l’utilizzo con il perno completo di meccanismo di
chiusura fornito. Sostituire il perno della ruota posteriore della bicicletta con quello
in dotazione. Assicurarsi che la leva di sgancio rapido si trovi sul lato sinistro della
bicicletta e sia rivolta verso l’alto.
2.1: Het trainingstoestel is ontworpen om met de meegeleverde ontgrendelingspen
gebruikt te worden. Vervang de ontgrendelingspen op het achterwiel van uw fiets
door de meegeleverde pen. Zorg ervoor dat de hendel voor snelle ontgrendeling zich
aan de linkerkant van de fiets bevindt en naar boven gericht is.
2.1:レーナーは付属のス使用す設計さ
イク後キュアー キュアー取り替えます。クイッリー
スハドルが自転車の左側に上向きになていを確認
2.1: The trainer is designed to be used with the provided quick release
skewer. Replace the quick release skewer on the rear wheel of your bike with
the one provided. Make sure the quick release lever is on the left (non-drive
side) of the bike.
2.1: El aparato de entrenamiento está diseñado para su uso con el cierre rápido
suministrado. Sustituya el cierre rápido de la rueda trasera de la bicicleta por el
suministrado. Asegúrese que la manivela de desacople rápido esté en el lado
izquierdo de la bicicleta y que apunte hacia arriba.
1.1
2.1
TRAINER SETUP
1.2
1.1: To open up your trainer, press the button and extend the legs as shown,
then set the trainer on a flat surface.
1.2: If the floor is not level, use the yellow dial on the left leg to adjust as
necessary.
1.1: Para montar el aparato de entrenamiento, extienda las patas tal como se indica
a continuación y colóquelo sobre una superficie plana.
1.2: Gire la ruedecilla para ajustar la pata y nivelar el bastidor como se muestra a
continuación.

Related product manuals