D-Link DGS-3000 series - Page 92

DGS-3000 Series Layer 2 Managed Gigabit Switch CLI Reference Guide
88
auto_assign - Specifies that the access ID will automatically be assigned.
<value 1-256> - Enter the access ID used here. This value must be between 1 and 256.
ethernet - Specifies to configure the ethernet access profile.
vlan - (Optional) Specifies the VLAN name.
<vlan_name 32> - Enter the name of the VLAN here. This name can be up to 32
characters long.
vlan_id - (Optional) Specifies the VLAN ID used.
<vlanid 1-4094> - Enter the VLAN ID used here. This value must be between 1 and 4094.
mask - (Optional) Specifies an additional mask parameter that can be configured.
<hex 0x0-0x0fff> - Enter the mask value here.
source_mac - (Optional) Specifies the source MAC address.
<macaddr> - Enter the source MAC address used for this configuration here.
mask - (Optional) Specifies an additional mask parameter that can be configured.
<macmask> - Enter the source MAC mask used here.
destination_mac - (Optional) Specifies the destination MAC address.
<macaddr> - Enter the destination MAC address used for this configuration here.
mask - (Optional) Specifies an additional mask parameter that can be configured.
<macmask> - Enter the destination MAC mask here.
802.1p - (Optional) Specifies the value of the 802.1p priority tag.
<value 0-7> - Enter the 802.1p priority tag value. The priority tag ranges from 1 to 7.
ethernet_type - (Optional) Specifies the Ethernet type.
<hex 0x0-0xffff> - Enter the Ethernet type mask here.
ip - Specifies to configure the IP access profile.
vlan - (Optional) Specifies a VLAN name.
<vlan_name 32> - Enter the name of the VLAN here. This name can be up to 32
characters long.
vlan_id - (Optional) Specifies that VLAN ID used.
<vlanid 1-4094> - Enter the VLAN ID used here. This value must be between 1 and 4094.
mask – (Optional) Specifies an additional mask parameter that can be configured.
<hex 0x0-0x0fff> - Enter the mask value here.
source_ip - (Optional) Specifies an IP source address.
<ipaddr> - Enter the source IP address used for this configuration here.
mask - (Optional) Specifies an additional mask parameter that can be configured.
<netmask> - Enter the source netmask used here.
destination_ip - (Optional) Specifies an IP destination address.
<ipaddr> - Enter the destination IP address used for this configuration here.
mask - (Optional) Specifies an additional mask parameter that can be configured.
<netmask> - Enter the destination netmask used here.
dscp - (Optional) Specifies the value of DSCP. The DSCP value ranges from 0 to 63.
<value 0-63> - Enter the DSCP value here.
icmp - (Optional) Specifies to configure the ICMP parameters.
type - (Optional) Specifies that the rule will apply to the ICMP Type traffic value.
<value 0-255> - Enter the ICMP type traffic value here. This value must be between 0
and 255.
code - (Optional) Specifies that the rule will apply to the ICMP Code traffic value.
<value 0-255> - Enter the ICMP code traffic value here. This value must be between 0
and 255.
igmp - (Optional) Specifies to configure the IGMP parameters.
type - (Optional) Specifies that the rule will apply to the IGMP Type traffic value.
<value 0-255> - Enter the IGMP type traffic value here. This value must be between 0
and 255.
tcp - Specifies to configure the TCP parameters.
src_port - (Optional) Specifies that the rule will apply to a range of TCP source ports.
<value 0-65535> - Enter the TCP source port value here. This value must be between
0 and 65535.
mask - (Optional) Specifies an additional mask parameter that can be configured.
<hex 0x0-0xffff> - Enter the source port mask here.
dst_port - (Optional) Specifies that the rule will apply to a range of TCP destination ports.
<value 0-65535> - Enter the TCP destination port value here. This value must be
between 0 and 65535.