xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide
416
Format
config erps raps_vlan <vlanid> [state [enable | disable] | ring_mel <value 0-7> | ring_port
[west [<port> | virtual_ch
annel] | east [
<port> | virtual_chann
el]] | rpl_port [
west | east
| none]
| rpl_owner [enable | disable] | protected_vlan [add | delete] vlanid <vidlist> | sub_ring
raps_vlan <vlanid> tc_propagation state [enable | disable] | [add |delete] sub_ring raps_vlan
<vlanid> | revertive [enable | disable] | timer {holdoff_time <millisecond 0-10000> |
guard_time <millisecond 10-2000> | wtr_time <min 5-12>}(1)]
Parameters
<vlanid> - The VLAN ID associated with the R-APS VLAN.
state - Specifies the ERPS R-APS VLAN state.
enable - Specifies that the ERPS R-APS VLAN state will be enabled.
disable - Specifies that the ERPS R-APS VLAN state will be disabled.
ring_mel - Specify the ring MEL of the R-APS function. The default ring MEL is 1.
<value 0-7> - Specify a value between 0 and 7.
ring_port - Specify a port participating in the ERPS ring.
west - Specify the port as the west ring port.
<port> - Specify a port.
virtual_channel - Specify the port as a west port on the virtual channel.
east - Specify the port as the east ring port.
<port> - Specify a port.
virtual_channel - Specify the port as an east port on the virtual channel.
rpl_port - By default, the node has no RPL port.
west - Specify the west ring port as the RPL port.
east - Specify the east ring port as the RPL port.
none - No RPL port on this node.
rpl_owner - By default, the RPS owner is disabled.
enable - Specify the device as an RPL owner node.
disable - This node is not an RPL owner.
protected_vlan - Specify VLANs that are protected by the ERPS function. The R-APS VLAN
cannot be the protected VLAN. The protected VLAN can be one that has already been
created, or it can be used for a VLAN that has not yet been created.
add - Add VLANs to the protected VLAN group
delete - Delete VLANs from the protected VLAN group.
vlanid - Specify a VLAN ID list.
<vidlist> - Specify a range of VLAN IDs.
sub_ring - Specifies the sub-ring configuration.
raps_vlan - Specify the R-APS VLAN.
<vlanid> - Enter the R-APS VLAN ID used here.
tc_propagation - Specifies to configure the state of the topology change propagation for
the sub-ring.
state - Specifies the propagation state of the topology change for the sub-ring.
enable - Enable the propagation state of the topology change for the sub-ring.
disable - Disable the propagation state of the topology change for the sub-ring.
add - Specifies the add a topology change propagation rule.
sub_ring - Specifies the sub-ring configuration information.
raps_vlan - Specify the R-APS VLAN
<vlanid> - Enter the R-APS VLAN ID used here.
delete - Specifies the delete a topology change propagation rule.
sub_ring - Specifies the sub-ring configuration information.
raps_vlan - Specify the R-APS VLAN.
<vlanid> - Enter the R-APS VLAN ID used here.
revertive - Specifies the revertive mode state.
enable - Specifies that the revertive mode will be enabled.
disable - Specifies that the revertive mode will be disabled.
timer - Configure the ERPS timers for a specific R-APS VLAN.
To Next Page
Loading...
