EasyManua.ls Logo

D-Link DSR-1000 - Page 246

D-Link DSR-1000
251 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
246
付録D ćƒ­ć‚°ćƒ”ćƒƒć‚»ćƒ¼ć‚ø
ćƒ­ć‚°ćƒ”ćƒƒć‚»ćƒ¼ć‚ø ē·Šę€„åŗ¦ ćƒ­ć‚°ćƒ”ćƒƒć‚»ćƒ¼ć‚ø ē·Šę€„åŗ¦
bcmDeviceInit: registration failed DEBUG try_module_get failed WARNING
bcmDeviceInit: pCdev Add failed DEBUG %s: request_irq failed, dev->name WARNING
REG Size == 8 Bit DEBUG too many virtual ap's (already got %d), sc->sc_nvaps WARNING
Value = %x ::: At Page = %x : Addr = %x DEBUG %s: request_irq failed, dev->name WARNING
REG Size == 16 Bit DEBUG rix %u (%u) bad ratekbps %u mode %u, WARNING
Value = %x ::: At Page = %x : Addr = %x DEBUG cix %u (%u) bad ratekbps %u mode %u, WARNING
REG Size == 32 Bit DEBUG %s: no rates for %s?, WARNING
Value = %x ::: At Page = %x : Addr =%x DEBUG no rates yet! mode %u, sc- >sc_curmode WARNING
REG Size == 64 Bit DEBUG %u.%u.%u.%u sent an invalid ICMP WARNING
REG Size is not in 8/16/32/64 DEBUG dst cache overī™±ow WARNING
Written Value = %x ::: At Page = %x : Addr = %x DEBUG Neighbour table overī™±ow. WARNING
bcm_ioctl :Unknown Ioctl Case : DEBUG host %u.%u.%u.%u/if%d ignores WARNING
=========Register Dump for Port Number #
%d=========,port
DEBUG martian destination %u.%u.%u.%u from WARNING
%s : Read Status=%s data=%#x,regName[j], DEBUG martian source %u.%u.%u.%u from WARNING
%s : Read Status=%s data=%#x,regName[j], DEBUG ll header: WARNING
powerDeviceInit: device registration failed DEBUG %u.%u.%u.%u sent an invalid ICMP WARNING
powerDeviceInit: adding device failed DEBUG dst cache overī™±ow WARNING
%s: Error: Big jump in pn number. TID=%d, from %x %x to %x
%x.
DEBUG Neighbour table overī™±ow. WARNING
%s: The MIC is corrupted. Drop this frame., __func__ DEBUG host %u.%u.%u.%u/if%d ignores WARNING
%s: The MIC is OK. Still use this frame and update PN., __func__
DEBUG martian destination %u.%u.%u.%u from WARNING
ADDBA send failed: recipient is not a 11n node DEBUG martian source %u.%u.%u.%u from WARNING
Cannot Set Rate: %x, value DEBUG ll header: WARNING
Getting Rate Series: %x,vap- >iv_ī™°xed_rate.series DEBUG %u.%u.%u.%u sent an invalid ICMP WARNING
Getting Retry Series: %x,vap- >iv_ī™°xed_rate.retries DEBUG dst cache overī™±ow WARNING
IC Name: %s,ic->ic_dev->name DEBUG Neighbour table overī™±ow. WARNING
usage: rtparams rt_idx <0|1> per <0..100> probe_intval
<0..100>
DEBUG host %u.%u.%u.%u/if%d ignores WARNING
usage: acparams ac <0|3> RTS <0|1> aggr scaling <0..4> min
mbps <0..250>
DEBUG martian source %u.%u.%u.%u from WARNING
usage: hbrparams ac <2> enable <0|1> per_low <0..50>
DEBUG ll header: WARNING
%s(): ADDBA mode is AUTO, __func__ DEBUG martian destination %u.%u.%u.%u from WARNING
%s(): Invalid TID value, __func__ DEBUG %u.%u.%u.%u sent an invalid ICMP WARNING
%s(): ADDBA mode is AUTO, __func__ DEBUG dst cache overī™±ow WARNING
%s(): Invalid TID value, __func__ DEBUG Neighbour table overī™±ow. WARNING
%s(): Invalid TID value, __func__ DEBUG host %u.%u.%u.%u/if%d ignores WARNING
Addba status IDLE DEBUG martian destination %u.%u.%u.%u from WARNING
%s(): ADDBA mode is AUTO, __func__ DEBUG martian source %u.%u.%u.%u from WARNING
%s(): Invalid TID value, __func__ DEBUG ll header: WARNING
Error in ADD- no node available DEBUG Unable to create ip_set_list ERROR
%s(): Channel capabilities do not match, chan ī™±ags 0x%x,
DEBUG Unable to create ip_set_hash ERROR
%s: cannot map channel to mode; freq %u ī™±ags 0x%x, DEBUG ip_conntrack_in: Frag of proto %u (hook=%u), ERROR
ic_get_currentCountry not initialized yet DEBUG Unable to register netī™°lter socket option ERROR
Country ie is %c%c%c, DEBUG Unable to create ip_conntrack_hash ERROR
%s: wrong state transition from %d to %d, DEBUG Unable to create ip_conntrack slab cache ERROR
%s: wrong state transition from %d to %d, DEBUG Unable to create ip_expect slab cache ERROR
%s: wrong state transition from %d to %d, DEBUG Unable to create ip_set_iptreeb slab cache ERROR
%s: wrong state transition from %d to %d, DEBUG Unable to create ip_set_iptreed slab cache ERROR
%s: wrong state transition from %d to %d, DEBUG %s: cannot allocate space for %scompressor, fname, ERROR
%s: wrong state transition from %d to %d, DEBUG %s: cannot allocate space for MPPC history, ERROR
ieee80211_deliver_l2uf: no buf available DEBUG %s: cannot allocate space for MPPC history, ERROR
%s: %s, vap->iv_dev->name, buf /* NB: no */ DEBUG %s: cannot load ARC4 module, fname ERROR
%s: [%s] %s, vap->iv_dev->name, DEBUG %s: cannot load SHA1 module, fname ERROR

Table of Contents

Other manuals for D-Link DSR-1000

Related product manuals