D-Link DSR-250N - Page 264

Unified Services Router User Manual
262
>ifName
Wakingup due to wow signal DEBUG unable to register KIFDEV to UMI ERROR
%s, wowStatus = 0x%x, __func__,
wowStatus
DEBUG
ERROR: %s: Timeout at page %#0x
addr %#0x
ERROR
Pattern added already
DEBUG
ERROR: %s: Timeout at page %#0x
addr %#0x
ERROR
Error : All the %d pattern are in use.
Cannot add a new pattern ,
MAX_NUM_PATTERN
DEBUG
Invalid IOCTL %#08x, cmd
ERROR
Pattern added to entry %d ,i
DEBUG
%s: unable to register device, dev-
>name
ERROR
Remove wake up pattern
DEBUG
ath_pci: 32-bit DMA not available
ERROR
mask = %p pat =
%p ,maskBytes,patternBytes
DEBUG
ath_pci: cannot reserve PCI memory
region
ERROR
mask = %x pat =
%x ,(u_int32_t)maskBytes,
(u_int32_t)patternBytes
DEBUG
ath_pci: cannot remap PCI memory
region) ;
ERROR
Pattern Removed from entry %d ,i
DEBUG
ath_pci: no memory for device state
ERROR
Error : Pattern not found
DEBUG
%s: unable to register device, dev-
>name
ERROR
PPM STATE ILLEGAL %x %x,
forcePpmStateCur, afp->forceState
DEBUG
ath_dev_probe: no memory for device
state
ERROR
FORCE_PPM %4d %6.6x %8.8x %8.8x
%8.8x %3.3x %4.4x,
DEBUG
%s: no memory for device state,
__func__
ERROR
failed to allocate tx descriptors: %d,
error
DEBUG
kernel MIBCTL registration failed!
ERROR
failed to allocate beacon descripotrs:
%d, error
DEBUG
Bad ioctl command
ERROR
failed to allocate UAPSD descripotrs:
%d, error
DEBUG
WpsMod: Failed to configure gpio pin
ERROR
hal qnum %u out of range, max %u!,
DEBUG
WpsMod: Failed to register interrupt
handler
ERROR
HAL AC %u out of range, max %zu!,
DEBUG
registering char device failed
ERROR
HAL AC %u out of range, max %zu!,
DEBUG
unregistering char device failed
ERROR
%s: unable to update hardware queue
%u!,
DEBUG
%s:%d - ERROR: non-NULL node
pointer in %p, %p<%s>!
ERROR
Multicast Q:
DEBUG
%s:%d - ERROR: non-NULL node
pointer in %p, %p<%s>!
ERROR
%p , buf
DEBUG
can't alloc name %s, name
ERROR
buf flags - 0x%08x --------- , buf-
>bf_flags
DEBUG
%s: unable to register device, dev-
>name
ERROR
buf status - 0x%08x, buf->bf_status
DEBUG
failed to automatically load module:
%s; \
ERROR
# frames in aggr - %d, length of
aggregate - %d, length of frame - %d,
sequence number - %d, tidno - %d,
DEBUG
Unable to load needed module: %s; no
support for \
ERROR
isdata: %d isaggr: %d isampdu: %d ht:
%d isretried: %d isxretried: %d
shpreamble: %d isbar: %d ispspoll: %d
aggrburst: %d calcairtime: %d
qosnulleosp: %d,
DEBUG
Module \%s\ is not known, buf
ERROR
%p: 0x%08x 0x%08x 0x%08x 0x%08x
0x%08x 0x%08x 0x%08x 0x%08x
0x%08x 0x%08x,
DEBUG
Error loading module \%s\, buf
ERROR
0x%08x 0x%08x 0x%08x 0x%08x
0x%08x 0x%08x 0x%08x 0x%08x
DEBUG
Module \%s\ failed to initialize, buf
ERROR